تقویت قاب خمشی فولادی با سیستم تیر به ستون پیوند شده (LCF) به روش تحلیل استاتیکی غیر‌خطی و تحلیل تاریخچه زمانی

نوع مقاله : مقاله پژوهشی

نویسندگان

1 استاد، دانشکده مهندسی عمران، دانشگاه سمنان

2 کارشناسی ارشدسازه دانشگاه سمنان

چکیده

برای این منظور سازه‌های سه و شش و نه طبقه بر مبنای پلان ساختمان‌های SAC در نظر گرفته ‌شده است. قاب‌های خمشی چهار و هشت و شانزده طبقه طبق ویرایش 1 و 4 آیین‌نامه طراحی ساختمان‌ها در برابر زلزله طراحی و در ادامه قاب‌های طراحی‌شده با ویرایش 1 توسط سیستم قاب با ستون پیوند شده تا رسیدن به تغییر مکان هدف، مقاوم‌سازی گردید. پس از آن قاب‌های مقاوم‌سازی شده و طراحی‌شده با ویرایش 1 و4 تحت 7 جفت شتاب ‌نگاشت حوزه دور و نزدیک تحلیل گردید. با توجه به نتایج حاصل از تحلیل استاتیکی غیر‌خطی و تحلیل دینامیکی تاریخچه زمانی درصد اختلاف نیرو در تغییر مکان هدف سازه‌ی طراحی‌شده طبق ویرایش 1 و 4 هدف 27 تا 50 درصد، درصد اختلاف تغییر شکل جاری‌شدگی سازه‌ی طراحی‌شده طبق ویرایش 1 به مقاوم‌سازی شده از حدود 5 تا 42 درصد، درصد اختلاف ضریب رفتار سازه‌های طراحی‌شده طبق ویرایش 1 و مقاوم‌سازی شده از 4 تا 40 درصد می‌باشد.در سازه‌ی 4 طبقه باعث کاهش جابجایی %13.34و کاهشی %14.06در IDR می‌شود. به‌طور مشابه، در مورد سازه‌های 8 طبقه، این کاهش به ترتیب %20.92برای جابجایی و%20.81برای IDR اندازه‌گیری می‌شود. در ارزیابی سازه‌ی 16 طبقه طراحی‌شده بر اساس ویرایش 1367 و اضافه کردن سیستم الحاقی، مشخص شد که افزودن سیستم الحاقی به سازه‌ی 16طبقه باعث کاهش تقریبی %51.43 در جابجایی و تقریبی %26.89در IDR می‌شود.افزودن سیستم الحاقی به سازه‌ی4 طبقه تغییرات معنی‌داری در جابجایی با %59.99و در IDR با %24.53ایجاد می‌کند. به‌مانند این در سازه‌ی 8 طبقه نیز، کاهش جابجایی %59.99و در IDR %22.82را تجربه می‌کنیم.

کلیدواژه‌ها

موضوعات


عنوان مقاله [English]

Investigation of the steel moment resisting frame retrofitted with the linked column frame system by nonlinear static analysis and time history analysis

نویسندگان [English]

  • majid gholhaki 1
  • Negar taheri 2
1 Professor of Structural Engineering, Dean of Faculty of Civil Engineering, Semnan University
2 MSc
چکیده [English]

For this purpose, three-, six-, and nine-story structures are considered based on the SAC building plan. four-, eight-, and sixteen-story bending frames were designed according to the 1st and 4th editions of the Regulations for the Design of Buildings against Earthquakes, and the frames designed with the 1st edition were designed by the frame and column system until the location of the target was changed. Subsequently, the reinforced and designed frames were analyzed using seven pairs of near- and far-field acceleration maps. According to the results of non-linear static analysis and dynamic analysis of the time history of the force difference percentage in the target displacement of the structure designed according to the 1st and 4th editions, the target is 27 to 50%, the percentage difference of the flow deformation of the structure designed according to the 1st edition to the retrofitted one is approximately 5–42%, and the percentage difference of the behavior coefficient of structures designed according to the 1st edition and retrofitted is from 4 to 40%. In a 4-story structure, this causes a 13.34% reduction in displacement and a 14.06% reduction in IDR. Similarly, in the case of 8-story structures, this reduction was measured as 20.92% for displacement and 20.81% for IDR. In the evaluation of the 16-story structure designed based on the1367 edition and the addition of the extension system, it was found that the addition of the extension system to the 16-story structure caused a decrease of approximately 51.43% in displacement and approximately26.89% in IDR.

کلیدواژه‌ها [English]

  • frame system with connected column
  • beam connection
  • retrofitting
  • far and near field accelerometer
  • steel bending frame