@article { author = {Yazdi, Seyed reza and Alimohammadi, Samira}, title = {Analysis of a Plane-Stress Problems using Matrix Free Galerkin Explicit Finite Volume Method for Unstructured Triangular Mesh}, journal = {Amirkabir Journal of Civil Engineering}, volume = {43}, number = {2}, pages = {1-8}, year = {2012}, publisher = {Amirkabir University of Technology}, issn = {2588-297X}, eissn = {2588-2988}, doi = {10.22060/ceej.2012.134}, abstract = {In this article,a new finite volume solver which uses a matrix free Galerkin approach for explicit solution of weak form of two dimensional Cauchy equilibrium equations is introduced. This method is suitable for linear structural problems for which two-dimensional assumption can be applied. In this work, the two dimensional equations of motion governing the plane stress problems are solved on unstructured triangular meshes.  In order to present the accuracy of computed results of introduced method, a plate test case under distributed load with available computed results from other numerical methods are utilized. The results presented in terms of stress and strain contours and compared with the available analytical solution.}, keywords = {Numerical modeling,Galerkin Finite Volume Method,Plane Stress Analysis,Unstructured Triangular Mesh}, title_fa = {تحلیل مسائل تحت بارگذاری تنش صفحه ای به روش بی نیاز از عملیات ماتریسی گالرکین حجم محدود}, abstract_fa = {دراین مقاله، روش جدید حل عددی بی­نیاز از عملیات ماتریسی گالرکین- حجم محدود، برای حل معادلات دوبعدی کاوشی دردیدگاه لاگرانژی حاکم بر تنش­های صفحه­ای، با فرض روابط خطی برای سازگاری تنش و تغییر شکل­ها، برروی المان­های مثلثی توسعه داده شده­است. معادله حرکت حاکم بر صفحات تحت تنش­های صفحه­ای توسط این روش در شبکه­های بی­ساختار گسسته­سازی شده­اند و تحلیل سازه به­صورت حل صریح و بدون نیاز به عملیات ماتریسی انجام شده است. برای ایجاد دید مهندسی و فیزیکی از نتایج تحلیل و هم­چنین ارزیابی کیفی جواب­های به­دست آمده از حل عددی برروی یک صفحه نمونه تحت تنش­های صفحه­ای، نتایج  بصورت مناطق رنگی هم­تنش و هم­تغییر شکل بر روی هندسه سازه ترسیم شده­اند و با حل تحلیلی آن و نتایج سایر روش­های عددی مقایسه شده  است . }, keywords_fa = {Numerical modeling,Galerkin Finite Volume Method,Plane Stress Analysis,Unstructured Triangular Mesh}, url = {https://ceej.aut.ac.ir/article_134.html}, eprint = {https://ceej.aut.ac.ir/article_134_c26fc309ede0fd35b7588a4b7f506038.pdf} } @article { author = {Shirdel, Mehdi and Ghanbari, Ali and Davoodi, Mohammad}, title = {Development of Pseudo-Static Method for Stability Analyses of Embankment Dams}, journal = {Amirkabir Journal of Civil Engineering}, volume = {43}, number = {2}, pages = {9-18}, year = {2012}, publisher = {Amirkabir University of Technology}, issn = {2588-297X}, eissn = {2588-2988}, doi = {10.22060/ceej.2012.135}, abstract = {Pseudo-static analysis is a common and simple method for the evaluation of seismic stability in embankment dams. Selection of the horizontal Pseudo-static coefficient is a primary step for evaluation of seismic behavior of embankment. Previous researchers and design manuals of embankment dams often suggest constant values for selecting the seismic coefficient regardless of site seismicity and the dynamic characteristics of the structures. In order to evaluate geometric effect, pseudo-static, static and dynamic analyses of the Masjed Soleiman dam With Finite Element Method performed and then precise a new equation to determine the pseudo-static coefficient of earth dams. In this equation, variations in acceleration for height of the dam, considered linear and the gradient of this line related to the geometrical characteristics of the dam body, soil stiffness and damping values. Result of this research imply that with increasing height of dam, decrease gradient of acceleration and with increasing slope of dam, increase gradient of acceleration. }, keywords = {Earth Dams,Pseudo Static,Dynamic Analyses؛ HORIZONTAL ACCELERATION COEFFICIENT؛ Seismicity}, title_fa = {توسعه روش شبه‌استاتیک برای تحلیل لرزه‌ای سدهای خاکی}, abstract_fa = {روش شبه‌استاتیک یکی از روش‌های کاربردی برای تحلیل لرزه‌ای سدهای خاکی به شمار می‌رود. انتخاب ضریب لرزه‌ای مناسب، اولین گام موثر برای رسیدن به نتایج مطلوب در این روش است. در گذشته نظرات زیادی بدون توجه به مشخصات هندسی، دینامیکی و هم‌چنین اثرات ساختگاه، برای تخمین ضریب شبه‌استاتیک ارائه شده است. بنابراین به منظور ارائه روشی دقیقتر، سد مسجد سلیمان به عنوان مطالعه موردی انتخاب شده و با بهره‌گیری از نتایج تحلیل‌های استاتیکی، شبه‌استاتیکی و دینامیکی با روش اجزاء محدود، به بررسی اثرات هندسه سد در تعیین ضریب شبه‌استاتیک پرداخته شده است. در رابطه پیشنهادی، تغییر شتاب در ارتفاع به صورت خطی فرض شده است. نرخ این تغییر در شتاب به خصوصیات هندسی بدنه سد، سختی خاک و مشخصات میرایی بستگی دارد. بنابراین در این تحقیق خصوصیات هندسی بررسی شده است. نتایج نشان می‌دهند که با افزایش ارتفاع بدنه سد خاکی، نرخ افزایش شتاب اعمالی کاسته شده و با تندتر شدن شیب بدنه، نرخ شتاب افزایش می‌یابد. به این ترتیب با در نظر گرفتن این تغییرات در ضریب شبه‌استاتیک پیشنهادی، در جهت دقیق نمودن روش شبه‌استاتیک، گام موثری برداشته شده است.}, keywords_fa = {Earth Dams,Pseudo Static,Dynamic Analyses؛ HORIZONTAL ACCELERATION COEFFICIENT؛ Seismicity}, url = {https://ceej.aut.ac.ir/article_135.html}, eprint = {https://ceej.aut.ac.ir/article_135_aebc6a3c21b4cc9730ff54b804e75189.pdf} } @article { author = {Ramezanianpour, Ali Akbar and Ghiasvand, Ebrahim and Kamel, Mohammad Ehsan}, title = {Durability of Concretes and Mortars Containing Limestone Powder Exposed to High Sulfate Environments}, journal = {Amirkabir Journal of Civil Engineering}, volume = {43}, number = {2}, pages = {19-25}, year = {2012}, publisher = {Amirkabir University of Technology}, issn = {2588-297X}, eissn = {2588-2988}, doi = {10.22060/ceej.2012.136}, abstract = {Sulfate attack is one of the most important problems concerning the durability of concrete structures. In this paper, the sulfate resistance of concrete and mortar specimens made from ordinary Portland cement containing limestone powder was studied. Strength reductions and mass changes of concrete specimens immersed in 10% Na2SO4 and MgSO4 solutions and Expansion of mortar prisms immersed in 5% and 10% Na2SO4 and MgSO4 solutions were monitored. It was observed that compressive strength decreases with the limestone replacement percent  and also, deterioration is severer, the higher the concentration content sulfate.}, keywords = {Sulfate Attack,Limestone Powder,Compressive Strength,Cement mortar expansion}, title_fa = {دوام بتن ها و ملات های دارای پودر سنگ آهک در محیط های سولفاتی با غلظت بالا}, abstract_fa = {در این مقاله، نتایج بررسی آزمایشگاهی بر روی اثر پودر سنگ­آهک بر دوام بتن­های قرار گرفته در محیط­های سولفاتی با غلظت بالا ارائه می­شود. به این منظور، نمونه­ها با 5 سطح جایگزینی سیمان توسط پودر سنگ­آهک، ساخته شد. در سنین مختلف، آزمایش­های تغییر مقاومت فشاری و وزن برروی نمونه­های بتنی که در محلول­های سولفات سدیم و منیزیم 10 درصد قرار داشتند انجام شد. هم­چنین نمونه­های منشوری ملات برای بررسی انبساط نمونه­ها، در محلول­های سولفات سدیم و منیزیم 5 و 10 درصد نگهداری شدند. بطور کلی دیده می­شود با افزایش میزان پودر سنگ­آهک، از مقدار مقاومت فشاری کاسته شده و شدت تخریب نمونه­ها در هر دو محلول سولفات با افزایش غلظت محلول، تشدید می­شود. }, keywords_fa = {Sulfate Attack,Limestone Powder,Compressive Strength,Cement mortar expansion}, url = {https://ceej.aut.ac.ir/article_136.html}, eprint = {https://ceej.aut.ac.ir/article_136_ab6506329e3ce3afa6bb10f8d5d1366b.pdf} } @article { author = {Amirodin Sadrnejad, Seyed and Ebrahimi, Bahram}, title = {Investigation on the Behavior of Concrete-Filled Rolled Steel Tubular Columns Under Axial Loads}, journal = {Amirkabir Journal of Civil Engineering}, volume = {43}, number = {2}, pages = {27-34}, year = {2012}, publisher = {Amirkabir University of Technology}, issn = {2588-297X}, eissn = {2588-2988}, doi = {10.22060/ceej.2012.137}, abstract = {In this paper, a numerical investigation on behavior of concrete in filled columns using nonlinear finite element method is done. Numerical results are verified using experimental results. Behavior of rolled steel tubes witch are filled with concrete of different strength on the axial applied loads is present. Effect of steel tubes thickness and confining stress are considered and the results are compared with concrete columns. The results showed that with increasing thickness of steel tubes, axial load capacity and confinement stress and ductility is increased and with increasing the concrete strength, confining stress and ductility is reduced. Specimens with different concrete strength of 30,60,80 MPaand different  ratioare analyzed and all the specimens have the same length of  300 mm. The main objects are: 1) to investigate effect of prominence on axial load capacity. 2) to investigate the effect of different parameters like thickness of steel tubes, friction coefficient and the ratio of prominence area over total perimeter area. 3) to investigate effect of loading(i.e. loading concrete only or loading concrete and steel tubes simultaneous. 4) to investigate the ductility of columns.}, keywords = {Composite Column,Finite element analysis,Confinement,Ductility index,Concrete,Steel Plate}, title_fa = {بررسی رفتار قالب‌های فولادی نورد شدهء پرشده با بتن زیر بار محوری فشاری}, abstract_fa = {در این مقاله بررسی‌های عددی گسترده‌ای بر روی رفتار قالب‌های پر شده با بتن به وسیله روش اجزا محدود غیرخطی انجام شده و درستی نتایج روش عددی با نتایج آزمایشگاهی بررسی شده است. رفتار ایننمونه‌ها، زیر بار محوری ارائه شده است. اثر ضخامت قالب فولادی و مقاومت چسبندگی بین بتن و فولاد و محصورشدگی بتن آزمایش شده و ظرفیت محوری نمونه‌ها و تنش محصورشدگی، محاسبه و با بتن معمولی مقایسه شده است. نتایج نشان دادندبا افزایش ضخامت ورق، ظرفیت باربری، تنش محصورشدگی و شکل‌پذیری افزایش می‌یابد و با افزایش مقاومت بتن، محصورشدگی هسته بتنی و شکل‌پذیری کاهش می‌یابد. نمونه‌ها با مقاومت بتن 30 و60 و80 مگاپاسکال و با نسبت D/tمتفاوت هستند و طول آنها 300 میلی متر است. مهم ترین اهداف آزمایش عبارتند از: 1-بررسی اثر وجود برجستگی بر ظرفیت باربری محوری. 2-بررسی عوامل مختلف مانند ضخامت قالب فولادی، ضریب اصطکاک و نسبت سطح برجستگی به سطح جانبی. 3-بررسی اثر نوع بارگذاری (فقط بارگذاری بتن و یا بتن و فولاد بصورت هم‌زمان). 4- بررسی شکل‌پذیری نمونه‌ها.  }, keywords_fa = {Composite Column,Finite element analysis,Confinement,Ductility index,Concrete,Steel Plate}, url = {https://ceej.aut.ac.ir/article_137.html}, eprint = {https://ceej.aut.ac.ir/article_137_8878cc15c96528703f25c5f443df1163.pdf} } @article { author = {Moeini, Hadi and Katibeh, Homayon and Golaabatoonch, Iraj}, title = {Upper Reservoir Seepage Analysis of Azad Dam Pumped Storage Power Station and Selecting the Best Sealing Method}, journal = {Amirkabir Journal of Civil Engineering}, volume = {43}, number = {2}, pages = {35-41}, year = {2012}, publisher = {Amirkabir University of Technology}, issn = {2588-297X}, eissn = {2588-2988}, doi = {10.22060/ceej.2012.138}, abstract = {Seepage analysis in the upper reservoir of the  Kurdistan Azad pumped storage dam with a volume of 3800000 cubic meter is an important and effective parameter for selecting of the optimized sealing method. More than 60% of the Lugeon test results show very permeable behavior. In order to calculate seepage discharge from the reservoir with no sealing element, analytical and numerical methods are used. Results of the analytical method and finite element numerical method (SEEP/W software) shown the amount of the seepage discharge in steady state flow is equal to 112600 and 11500 m3/day, respectively. Unsteady state numerical method (UDEC software) showed initial seepage discharge about 1700000 m3/day, decreasing to 112400m3/day while approaching to steady state conditions. 3D seepage modeling using Seep3D software shows about 118000 m3/day seepage discharge, means 3% of the total reservoir volume. Analysis show the necessity of sealing in the reservoir. After feasibility study, the geomembrane method was suggested as the best sealing method with the implementation cost of 20 billion Rls.}, keywords = {Kurdistan Azad Pumped storage Dam,Seepage analysis,seep/w,UDEC,Sepp/3D,Sealing methods}, title_fa = {تحلیل نشت مخزن ذخیرة آب نیروگاه تلمبه ‏ذخیره‏ای سد آزاد و گزینش روش بهینه آب‏بندی}, abstract_fa = {بررسی فرار آب از مخزن بالایی دست نیروگاه تلمبه‌­ذخیره­ای سد آزاد کردستان، یکی از عوامل مهم و اثر­گذار در آب­بندی مخزن است. در این تحقیق با توجه به مقدار نفوذپذیری دیواره‏ها و کف مخزن که از آزمایش­های لوژن به دست آمده، میزان نشت آب به چند روش محاسبه شده است. نتایج معادله تحلیلی ودرنیکف، روش عددی المان محدود (نرم‏افزار SEEP/W)، مقدار کل نشت آب از مخزن مورد نظر را در حالت جریان پایدار، به ترتیب برابر با 112600، 115500 متر مکعب در روز نشان داده‏اند. در روش عددی المان مجزا (نرم‏افزار UDEC) میزان نشت در لحظات آغازین جریان نشت در حالت جریان ناپایدار 1700000 متر مکعب بر روز برآورد شد. این مقدار نشت که مقداری قابل ملاحظه است. با گذشت زمان از دبی نشت کاسته شده و این دبی به دبی حالت پایدار یعنی 112400 متر مکعب در روز نزدیک می‏شود.  در شبیه­سازی سه بعدی مخزن، از نرم‏افزار Seep/3D استفاده شد که مقدار نشت کلی آب در حالت پایدار را در حدود 118،000 متر مکعب (معادل 3 درصد از حجم کل) در روز نشان داد. با در نظر گرفتن نتایج بدست آمده از محاسبات نشت، احداث المان آب‏بند برای جلوگیری از فرار آب از مخزن ضروری به نظر می‏رسد. در این تحقیق، پس از بررسی جنبه‏های فنی و اقتصادی روش‏های آب­بندی، روش بهینه آب‏بندی به کمک ژئوممبرین با صرف هزینه‏ای معادل20میلیارد ریال پیشنهاد گردید. }, keywords_fa = {Kurdistan Azad Pumped storage Dam,Seepage analysis,seep/w,UDEC,Sepp/3D,Sealing methods}, url = {https://ceej.aut.ac.ir/article_138.html}, eprint = {https://ceej.aut.ac.ir/article_138_ba602d30e2ae4f81be423e1c1a848f84.pdf} } @article { author = {Qaderi Zefrehei, Farhad and Ayati, Bita and Ganjidoust, Hosein}, title = {Comparing the Efficiency of MBBR and SBR in Treating Wastewater Containing Formaldehyde}, journal = {Amirkabir Journal of Civil Engineering}, volume = {43}, number = {2}, pages = {43-50}, year = {2012}, publisher = {Amirkabir University of Technology}, issn = {2588-297X}, eissn = {2588-2988}, doi = {10.22060/ceej.2012.139}, abstract = {Nowadays formaldehyde is used in many industrial activities such as adhesives, resins and paper producing, pharmaceutics, and also a number of general and commercial activities like some hospital services, dead burial and providing the sanitation of some public places like garrisons. In this research aerobic treatment of formaldehyde in MBBR compared with SBR in the influent COD range between 0 to 2500 mg/L. According to the results, SBR under serial operation was better than MBBR. These results showed the removal efficiency of influent CODs less than 200 mg/L was 100% and for CODs between 200 to 450 mg/L was 90% after 48 hours. In this study, it took 4 days in CODs less than 1500 mg/L and 4 to 6 days in CODs between 1500 to 2500 mg/L for reactors to reach steady state condition. In kinetic study, related coefficients followed Stover-Kincannon second order model. 13C-NMR spectroscopy showed that formaldehyde and urea was converted to N-{[(amino-­carbonyl) amino] methyl} urea. It was determined formaldehyde was polymerized in ordinary temperature and all molecules including carbons were degraded.}, keywords = {biological,aerobic,COD,kinetic,13C-NMR spectroscopy}, title_fa = {مقایسه کارایی راکتور بیوفیلمی با بستر متحرک (MBBR) و راکتورهای ناپیوسته متوالی (SBR) در حذف فرمالدئید از فاضلاب}, abstract_fa = {امروزه فرمالدئید در بسیاری از فعالیت­های صنعتی مانند تولید چسب و رزین، کاغذ، دارو و هم­چنین تعدادی از فعالیت­های تجاری- عمومی از قبیل برخی خدمات بیمارستانی، کفن و دفن اموات و تامین بهداشت برخی اماکن عمومی مانند سربازخانه­ها کاربرد دارد. در این تحقیق تصفیه هوازی فرمالدئید در راکتورهای بیوفیلمی با بستر متحرک و ناپیوسته متوالی در محدوده COD ورودی صفر تاmg/L  2500 مقایسه شده است. بر اساس نتایج حاصل، راندمان حذف 100 درصد در CODهای ورودی کمتر از mg/L200 و بیش از 90 درصد در COD­های بین 200 تا 450 میلی­گرم بر لیتر پس از 48 ساعت در هر دو سامانه بدست آمده است. اما بطور کلی سامانه SBR در بهره­برداری سری نسبت به MBBR مناسب­تر بوده است. در این بررسی، برای رسیدن راکتورها به حالت پایدار در COD کمتر از mg/L1500، چهار روز و در COD، 1500 تا mg/L2500 چهار الی شش روز زمان نیاز بود. در بررسی سینتیک واکنش­های بیولوژیکی پایلوت­ها، ضرایب قابل قبولی برای طرح مرتبه دوم استاورکینکانن بدست آمد. هم­چنین در آزمایش CNMR با تبدیل فرمالدئید و اوره ورودی به آمینوکربنیل­آمینومتیل­اوره، مشخص شد که فرمالدئید در دمای معمولی پلیمر تشکیل می­دهد و همه مولکول­های دارای اتم کربن تجزیه       می­شوند. }, keywords_fa = {biological,aerobic,COD,kinetic,13C-NMR spectroscopy}, url = {https://ceej.aut.ac.ir/article_139.html}, eprint = {https://ceej.aut.ac.ir/article_139_c5ee7fceed617118de52952b6a5a448e.pdf} } @article { author = {Shakeri, Eghbal and Darabi, Moslem and Torabi Z, Mehdi}, title = {Detect of Accident Causes in Construction Workplace}, journal = {Amirkabir Journal of Civil Engineering}, volume = {43}, number = {2}, pages = {51-61}, year = {2012}, publisher = {Amirkabir University of Technology}, issn = {2588-297X}, eissn = {2588-2988}, doi = {10.22060/ceej.2012.141}, abstract = {Despite today's huge improvements in construction engineering and management methods, construction projects are considered as the riskiest workplaces. The work cure at this projects sites more than others are at risk. Hence, special attention to safety in these workplaces is needed to reduce the rate of accidents. However, the project stakeholders’ commitments to safety requirements are not evident at the regular arrangements. The aim of this study is to analyze the most common type of accidents and their consequences identified based on statistical and surveys in Iran construction projects and especially in Isfahan. Results shows that in building workplaces, human and organizational factors are the main sources of accidents. It also shows that project parties including owner, consultant and contractor are not familiar with safety rules and regulations and the lack of dedication, conviction and adequate supervision make this conditions worst. }, keywords = {Safety,Accident,Effect Factors,Accident cause}, title_fa = {بررسی و ریشه‌یابی عوامل خطرآفرین در کارگاه‌های ساختمانی}, abstract_fa = {امروزه با وجود صنعتی شدن روش‌های ساخت، ساخت و ساز بعنوان یکی از پرخطرترین صنایع در جهان است. در میان فعالان این صنعت، افرادی که در کارگاه‌های ساختمانی حضور دارند، بیش از دیگران در معرض خطر هستند. از این‌رو توجه به ایمنی در کارگاه‌های ساختمانی جایگاه خاصی در کاهش نرخ بروز حوادث در پروژه‌ها دارد. این در حالی است که ذینفعان پروژه‌ها توجه و تعهد چندانی به ایمنی نداشته و آنرا جزئی از کار و امری بدیهی می‌دانند. در این تحقیق هدف آن است که بر پایه مطالعات میدانی (آماری و پرسشنامه) در سطح کشور و بخصوص شهر اصفهان، متداول‌ترین نوع حوادث و پیامدهای آنها شناسایی شود و با معرفی اصلی‌ترین عوامل وقوع حوادث بتوان ذینفعان پروژه‌ها را برای کاهش هرچه بیش‌تر حوادث کارگاهی راهنمایی نمود. نتایج مطالعات میدانی نشان می‌دهد از آن است که عوامل انسانی و سازمانی کارگاه‌های ساختمانی بخش زیادی از علل بروز حوادث را به خود اختصاص داده است و عوامل اصلی قراردادی ساخت و ساز (کارفرما، مشاور و پیمانکار)، آنچنان با قوانین و آیین­نامه‌های ایمنی آشنایی ندارند و در صورت آشنایی، نظارت از سوی عوامل بالادستی بر بکارگیری این اسناد وجود ندارد.}, keywords_fa = {Safety,Accident,Effect Factors,Accident cause}, url = {https://ceej.aut.ac.ir/article_141.html}, eprint = {https://ceej.aut.ac.ir/article_141_e5af4e2d37af8145f58748c15d21c11f.pdf} } @article { author = {karblaie, Mohammad and sohrabi, mohammad reza}, title = {Study and Comparison of Compressive Strength Of Concrete Containing Crumb Rubber And Rubber Powder With Nano Silica}, journal = {Amirkabir Journal of Civil Engineering}, volume = {43}, number = {2}, pages = {63-70}, year = {2012}, publisher = {Amirkabir University of Technology}, issn = {2588-297X}, eissn = {2588-2988}, doi = {10.22060/ceej.2012.142}, abstract = {A large amount of rubbers are produced in the world, and the disposal of these waste materials is not feasible, as the rate of decomposition for tyre is very slow.  These waste material produce big environmental pollution, therefore optimum use of them has become a necessity. These kinds of trashes can be used for improving some mechanical properties of concrete. In this regard compressive strength of concrete specimens containing crumb rubber, rubber powder, along with nanosilica have been discussed at the ages of 7 and 28 days in the current research. A fixed water – cement ratio has been considered in the mixes. Crumb rubber particles ranging in size from 4.75 to 9.50 mm, and rubber powder of size 0.6 mm have been used.  In this paper 5%, 10%, 15% (by weight of cement) of rubber have been used, and also 2% and 3% nanosilica were added to the mixes containing rubber.  The results showed an improvement in the failure behavior, and compressive strength growth of concrete containing rubber and nanosilica.}, keywords = {Concrete,powder rubber,Crumb Rubber,Nanosilica,compression resistance}, title_fa = {بررسی و مقایسه مقاومت فشاری بتن دارای خرده لاستیک و پودر لاستیک به همراه نانوسیلیس}, abstract_fa = {به طور کلی لاستیک­های بسیار زیادی در جهان تولید می­شود و امکان دفع این زباله­ها در محیط زیست وجود ندارد؛ زیرا تایر با سرعت بسیار کمی تجزیه می­شود؛ و آلودگی­های زیادی تولید می­نماید؛ بنابر­این استفاده بهینه از این ضایعات به یک ضرورت تبدیل شده است. از ضایعات می­توان برای بهبود برخی خواص مکانیکی بتن استفاده نمود. در همین راستا در تحقیق حاضر، خواص مقاومت فشاری 7 روزه و 28 روزه خرده لاستیک و پودر لاستیک به همراه نانوسیلیس مورد بررسی قرار گرفته است. نسبت آب به سیمان در طرح­ها ثابت بوده و از خرده لاستیک به ابعاد  5/9 - 75/4 میلی­متر و پودر لاستیک  به ابعاد 6 /0 میلی­متر استفاده شده است. در این مقاله مقدار لاستیک به صورت درصد وزنی سیمان 5% ،10% و 15% استفاده شده و نانوسیلیس به میزان 2% و3% به مخلوط­های دارای لاستیک اضافه شده است که شاهد بهبود نحوه شکست و افزایش مقاومت فشاری در این نوع بتن هستیم.}, keywords_fa = {Concrete,powder rubber,Crumb Rubber,Nanosilica,compression resistance}, url = {https://ceej.aut.ac.ir/article_142.html}, eprint = {https://ceej.aut.ac.ir/article_142_4c3c9d9711b77b6341a1770a55fae086.pdf} }