@article { author = {Mosavi Fard, Sayyed Jalal and Reisi, Mohammad}, title = {Influence evaluation of key mix design parameters of reactive powder concrete on compressive strength}, journal = {Amirkabir Journal of Civil Engineering}, volume = {52}, number = {11}, pages = {2663-2676}, year = {2021}, publisher = {Amirkabir University of Technology}, issn = {2588-297X}, eissn = {2588-2988}, doi = {10.22060/ceej.2019.16047.6114}, abstract = {Reactive powder concrete (RPC) is a new type of high performance concrete (HPC) which due to using fine powder and pozzolanic materials as well as high amount of materials which are hydraulically active, is known as this name. RPC characteristics have a high sensitivity to type and characteristics of materials used in RPC; therefore, in order to achieve desired physical and mechanical properties, it is necessary to carefully consider selection of materials and mix proportions. The purpose of this research was to investigate the effect of water to ementitious materials ratio (W/CM), amount of cementitious materials (CM), silica fume to cementitious materials ratio (SF/CM), cement type and grading of silica sand on compressive strength of RPC. To do so, 21 RPC mixes were designed and made. In each step of this research, one of the effective parameters were studied and accoding to obtained results, the next steps were performed. RPC specimens were cured in 90 oC water for 7 days. Results showed that by using cement type V, cementitious materials of 1100 kg/m3, water to cementitious materials ratio equal to 0.2, silica fume to cementitious materials ratio equal to 0.2 and use of silica sand with the the finest grading, the highest compressive strength can be achieved.}, keywords = {Reactive Powder Concrete (RPC),Water to cementitious materials ratio,Silica fume,Compressive Strength}, title_fa = {ارزیابی تأثیر پارامترهای کلیدی طرح اختلاط بتن پودری واکنشی (RPC) بر مقاومت فشاری}, abstract_fa = {تن پودری واکنشی نوع جدیدی از بتن‌های توانمند است که به دلیل ریزی مواد پودری و پوزولانی مورد استفاده در آن و نیز مقدار زیاد موادی که به صورت هیدرولیکی فعال هستند، به این نام شناخته می‌شود. مشخصات بتن پودری واکنشی، حساسیت زیادی به نوع و مشخصات مصالح مورد استفاده در ساخت آن دارد؛ بنابراین برای دستیابی به مشخصات فیزیکی و مکانیکی مطلوب لازم است در انتخاب مصالح و انتخاب نسبت‌های مخلوط دقت نمود. هدف از تحقیق حاضر، بررسی تأثیر نسبت آب به مواد سیمانی (W/CM)میزان مواد سیمانی(CM ،)نسبت دودهسیلیس به مواد سیمانی(SF/CM )نوع سیمان و نوع دانه‌بندی ماسه‌ی سیلیسی بر مقاومت فشاری RPC بود؛ بدین منظور 21 مخلوط بتن پودری واکنشی طراحی و ساخته شد. در هر گام از انجام این تحقیق، یکی از پارامترهای موثر بررسی شد و بر اساس نتایج بدست امده گام‌های بعدی تحقیق انجام شد. نمونه‌های ساخته شده به مدت 7 روز در آب 90 عمل‌آوری شدند. نتایج بدست m3/kg 1100 ،نسبت آب به مواد سیمانی برابر 0/2 ، آمده نشان داد که با استفاده از سیمان تیپ 5 ،مواد سیمانی به میزان نسبت دودهسیلیس به مواد سیمانی برابر 0/2 و استفاده از ماسه‌ی سیلیسی با ریزترین دانه‌بندی، می‌توان به بیشترین مقاومت فشاری دست یافت.}, keywords_fa = {بتن پودری واکنشی,نسبت آب به مواد سیمانی,دوده‌سیلیس,ماسه‌ی سیلیسی,مقاومت فشاری}, url = {https://ceej.aut.ac.ir/article_3624.html}, eprint = {https://ceej.aut.ac.ir/article_3624_9c6f3ddbf028aec05d510b219e437664.pdf} } @article { author = {mirjalili, ali and morshed, reza and Eslami, Abolfazl}, title = {Investigating the effect of vertical load on the behavior of adobe walls under cyclic lateral loading}, journal = {Amirkabir Journal of Civil Engineering}, volume = {52}, number = {11}, pages = {2677-2690}, year = {2021}, publisher = {Amirkabir University of Technology}, issn = {2588-297X}, eissn = {2588-2988}, doi = {10.22060/ceej.2019.16076.6118}, abstract = {Adobe constructions are vulnerable to lateral loading and their failure in the past earthquakes has caused severe casualties and structural damages. Nonetheless, numerous adobe buildings are still being used in seismic-prone regions worldwide, including Iran, many are of historical background. Therefore, evaluation of their lateral behavior and retrofitting stands of high priority and can lead to preserving these national assets. In this study, the cyclic lateral behavior of adobe walls made of adobe units and mud mortar was investigated under different constant axial loads. The experimental specimens were comprised of four adobe wall panels measuring 1000 mm in length, 900 mm in height, and 200 mm in thickness. The main experimental parameter was the magnitude of axial compression applied on the wall. The experimental results were compared in terms of load-displacement hysteretic curves, cracking pattern, failure mode, stiffness degradation, cumulative energy dissipation, and hysteretic damping. With increasing axial stress from 0.1 to 0.7 MPa, the failure mode was changed from shear to shear-compression. Also, with increasing axial stress, lateral resistance increased, but the corresponding displacement decreased.}, keywords = {Adobe wall,Failure mode,Cyclic loading,Lateral Strength,Hysteretic damping}, title_fa = {بررسی تأثیر سربار قائم بر رفتار دیوارهای خشتی تحت بار جانبی چرخه‌ای}, abstract_fa = {ساختمان‌های خشتی از بناهای آسیب‌پذیر در برابر بارهای جانبی محسوب می‌شوند، به طوری که خرابی آنها در زلزله‌های گذشته با خسارت و تلفات جانی زیادی همراه بوده است. با این وجود، هنوز ساختمان‌های خشتی زیادی در مناطق لرزه‌خیز جهان از جمله در کشور ایران در حال استفاده است که بسیاری از آنها دارای ارزش تاریخی نیز هستند. لذا، شناخت رفتار این گونه ساختمان‌ها در برابر بارهای جانبی از اهمیت به سزایی برخوردار بوده و منجر به اتخاذ تصمیم مناسب در چگونگی حفظ بنا خواهد شد. در تحقیق حاضر رفتار جانبی دیوارهای ساخته شده از خشت و ملات گل که تحت اثر بار محوری ثابت قرار داشتند، تحت بارگذاری جانبی چرخه‌ای مورد ارزیابی قرار گرفت. نمونه‌های آزمایشگاهی شامل 4 دیوار خشتی به طول 1000 میلی‌متر، ارتفاع 900 میلی‌متر و ضخامت 200 میلی‌متر بودند. متغیر اصلی آزمایشگاهی، تنش محوری قائم روی نمونه‌های دیوار بود. نتایج آزمایشگاهی به صورت منحنی‌های چرخه‌ای بار-جابجایی، الگوی ترک‌خوردگی، مد شکست، افت سختی، اتلاف انرژی تجمعی و میرایی چرخه‌ای با یکدیگر مقایسه گردیدند. بر اساس نتایج تحقیق، میزان تنش محوری دیوار تاثیر زیادی روی نحوه شکست و رفتار دیوار خشتی تحت بارهای جانبی و در نتیجه اتخاذ روش مناسب مقاوم سازی دارد. با افزایش تنش محوری از 0/1به 0/7 مگاپاسکال مد شکست از گهواره ای-برشی به برشی - فشاری تغییر کرد. همچنین با افزایش تنش محوری مقاومت جانبی افزایش اما جابجایی متناظر شکست کاهش یافت.}, keywords_fa = {دیوار خشتی,مد شکست,بار چرخه‌ای,مقاومت جانبی,میرایی چرخه‌ای}, url = {https://ceej.aut.ac.ir/article_3528.html}, eprint = {https://ceej.aut.ac.ir/article_3528_1cc609d0ac2d16520e5ce9739b1f2bb3.pdf} } @article { author = {Khodayari, Rasoul and bahar, omid}, title = {Identification of Story Stiffness of Shear Buildings under Ambient Vibration Tests with Highly Noise polluted Data}, journal = {Amirkabir Journal of Civil Engineering}, volume = {52}, number = {11}, pages = {2691-2712}, year = {2021}, publisher = {Amirkabir University of Technology}, issn = {2588-297X}, eissn = {2588-2988}, doi = {10.22060/ceej.2019.16095.6123}, abstract = {In recent years, Vibration Based System Identification (VBSI) as a powerful tool to disclosure a mathematical expression of dynamic behaviors of structures, is taken into consideration for structure engineers. Among developed strategies for VBSI, the strategies identifying under ambient vibration tests without using input data, with no limitation in serviceability and no need to complex excitation tools, have been more desirable. In some cases, regarding to high numbers of Degrees Of Freedom (DOFs) and impossibility of recording in whole DOFs, it is necessary to identify physical characteristics beside modal parameters with recording in limited numbers of DOFs. Among those physical characteristics, stiffness parameter is more important. The main goal of this paper is to present a method for identification of story stiffness in shear type buildings using incomplete structural responses. At the first, the sub matrix of structural stiffness matrix is identified by the proposed method based on the structural dynamics theory and the realization theory-based Stochastic Subspace Identification (SSI) method and then story stiffness will be available. Since the presence of noise is imaginable in ambient vibration tests, effects of noise also been investigated. To evaluate the proposed method, a five-story & twelve-story analytical shear buildings are studied. Extensive analysis show the high ability and accuracy of proposed method in correct identification of story stiffness from incomplete output records even in presence of noise.}, keywords = {System identification,story stiffness,ambient excitation,incomplete measurement,shear type buildings}, title_fa = {شناسایی سختی طبقات در ساختمان‌های برشی با استفاده از آزمایش ارتعاش محیطی با نوفه بالا}, abstract_fa = {شناسایی سیستم بر پایه داده‌برداری ارتعاش سازه به عنوان ابزاری قدرتمند برای رسیدن به یک مدل ریاضی از رفتار دینامیکی سازه در سال‌های اخیر مورد توجه مهندسان سازه قرار گرفته است. از میان رویکردهای توسعه یافته، رویکردهای مبتنی بر استفاده از داده‌های آزمایش ارتعاش محیطی که بدون نیاز به ابزارهای تحریک پیچیده و بدون محدودیت توقف در سرویس‌دهی سازه، به شناسایی سیستم می‌پردازند، از محبوبیت بیشتری برخوردارند. با توجه به تعداد بالای درجات آزادی در برخی سازه‌ها و عدم امکان داده‌برداری در تمام درجات آزادی، در مواقعی لازم است تا داده‌برداری در درجات آزادی محدودی انجام گرفته و علاوه بر تعیین پارامترهای مدی، مشخصه‌های فیزیکی نیز شناسایی گردند. از میان مشخصه‌های فیزیکی سازه، مشخصه‌ی سختی در مسائل تشخیص خرابی دارای اهمیت بیشتری است. هدف این مقاله ارائه‌ی روشی جهت شناسایی سختی طبقات در ساختمان‌های برشی با استفاده از داده‌های پاسخ ناکامل خروجی است. بر اساس روش پیشنهادی که بر پایه تئوری‌های دینامیک سازه‌ها و روش شناسایی زیرفضای تصادفی استوار است، نخست زیرماتریس سختی شناسایی شده و سپس با معادلات ساده ریاضی سختی طبقات تعیین می‌گردند. از آنجایی که در آزمایش ارتعاش محیطی، وجود نوفه دور از انتظار نمی‌باشد، در این مقاله اثرات نوفه نیز مورد بررسی قرار گرفته است. برای ارزیابی روش پیشنهادی از مدل تحلیلی سازه‌ی پنج طبقه و بیست طبقه‌ی برشی استفاده شده است. تحلیل‌های گسترده توانمندی و دقت روش پیشنهادی را در شناسایی صحیح سختی طبقات در داده‌برداری‌های ناکامل حتی در حضور نوفه را تایید می‌کنند.}, keywords_fa = {شناسایی سیستم,سختی طبقه,تحریکات محیطی,داده‌برداری ناکامل,ساختمان‌های برشی}, url = {https://ceej.aut.ac.ir/article_3596.html}, eprint = {https://ceej.aut.ac.ir/article_3596_e054f753c0e42524ff95f5113bf5da8f.pdf} } @article { author = {Hasani Moghaddam, Amin and Hashemi, Seyed Hossein and Ghadiri, Ali}, title = {Polycyclic Aromatic Hydrocarbons (PAHs) in Urban Runoff Sediments (Case Study: Tehran City)}, journal = {Amirkabir Journal of Civil Engineering}, volume = {52}, number = {11}, pages = {2713-2726}, year = {2021}, publisher = {Amirkabir University of Technology}, issn = {2588-297X}, eissn = {2588-2988}, doi = {10.22060/ceej.2019.16098.6124}, abstract = {Polycyclic aromatic hydrocarbons (PAHs) are of special importance because of their toxicity, stability, lipophilicity, bioaccumulation, carcinogenesis and mutagenic impacts on living organisms and human. Urban runoff contains significant amounts of PAH compounds, which result in transfer them to receiving environments and have significant environmental and health risks. Because of the hydrophobicity characteristic, transport of these compounds in aquatic environment, mainly coupled to suspended particles and sediments. Hence, evaluation of sediments is considered as one of the environments that affect the fate and transport of these compounds. Present study was performed to evaluating the concentrations and sources of PAH compounds in sediments of Tehran urban runoff network. The sediment samples were taken from the three main sub catchments of Tehran city in April 2017 and the concentration of 16 priority PAH compounds and organic carbon was measured and finally their probable emission sources were determined using five indexes of diagnostic ratios. The total PAHs concentration in three sub-catchments ranged from 57 to 978.2 ng / g dry weight. Also, distribution of concentrations in sub- catchment 2(57-976.6 ng/g) was higher than the sub[1]catchment 1(84.4-773.2 ng/g) and Sub-catchment 3(76.3–978.2 ng/g) due to the locating in center of the city and the diversity of pollutant sources. Moreover, the survey of the relationship between total organic carbon and PAHs showed a significant and strong correlation between these two variables, but its coefficient varied in each sub-catchments. At all stations except the station C1S27, 3 and 4 rings compounds in comparison with the other compounds had significant dominance. Four indexes showed the origin of compounds at all stations are pyrogenic and The LMW/HMW index showed that the source of contamination in 30% of the stations is petrogenic. Generally, the results showed that the portion of pyrogenic sources is significantly higher due to high population density, traffic and human activities.}, keywords = {sediment,polycyclic aromatic hydrocarbons,total organic carbon,Runoff,source identification}, title_fa = {هیدروکربن‌های حلقوی معطر (PAHs) در رسوبات رواناب شهری (مطالعه موردی شهر تهران)}, abstract_fa = {هیدروکربن‌های حلقوی معطر (PAHs )به‌دلیل سمیت، پایداری، چربی دوستی، تجمع زیستی و اثرات سرطانزایی و جهش‌زایی مورد توجه ویژه هستند. رواناب‌های شهری مقادیر قابل توجهی ترکیبات PAHs دارند که انتقال آنها به محیط‌های پذیرنده مخاطرات محیط زیستی و بهداشتی در پی دارد. به‌دلیل ویژگی آبگریزی، بیش‌تر این ترکیبات در محیط‌های آبی به‌صورت هم پیوند با ذرات معلق و رسوبات تجمع و انتقال می‌یابند. بنابراین ارزیابی رسوبات به‌عنوان یکی از محیط‌های موثر بر سرنوشت آنها اهمیت دارد. این پژوهش با هدف ارزیابی مقدار و منشا ترکیبات PAHs در رسوبات رواناب تهران انجام شده است. نمونه‌ها از سه زیرحوضه اصلی شهر تهران در اردیبهشت 1396 برداشت و غلظت 16 ترکیب PAHs و کربن آلی اندازه‌گیری و با پنج شاخص نسبت‌های تشخیصی، منابع انتشار محتمل آنها تعیین شد. غلظت مجموع PAHs در گستره57 تا2/978 نانوگرم برگرم وزن خشک رسوب بود. پراکندگی غلظت کل ترکیبات در زیرحوضه 2(57- 976/6 نانوگرم برگرم) به‌دلیل قرارگیری در مرکز شهر و تنوع منابع آلاینده نسبت به زیرحوضه 1(84/4 -773/2 نانوگرم بر گرم)و زیرحوضه 3(76/3 -978/2 نانوگرم بر گرم) بالاتر بود. همچنین، بین کربن آلی کل و غلظت PAHs همبستگی معنی‌دارو قوی وجود دارد، اما ضریب آن در هر زیرحوضه متفاوت است. در تمام ایستگاه‌ها به استثنای ایستگاه C1S27 ،ترکیبات 3 و 4 حلقه‌ای به‌ویژه کرایزن، فلئورانتن و پایرن غالب بودند. چهار شاخص منشاء ترکیبات را پایروژنیک و شاخصHMW/LMW در 30 درصدایستگاه‌ها منشاء پتروژنیک نشان داد. به‌طور کلی، به‌دلیل تراکم بالای جمعیت و ترافیک و فعالیت‌های انسانی، منابع پایروژنیک نسبت به پتروژنیک سهم غالب را دارند.}, keywords_fa = {رسوب,هیدورکربن های حلقوی معطر,کربن آلی کل,رواناب,منشایابی}, url = {https://ceej.aut.ac.ir/article_3562.html}, eprint = {https://ceej.aut.ac.ir/article_3562_a426f7904e0da258e39cf581515823ba.pdf} } @article { author = {Amiri, Mohammad and Dehghani, Masoud and papi, maedeh}, title = {Microstructural Analysis of Thermally Induced Changes in Permeability Coefficient and Settlement of Marl Soils}, journal = {Amirkabir Journal of Civil Engineering}, volume = {52}, number = {11}, pages = {2727-2742}, year = {2021}, publisher = {Amirkabir University of Technology}, issn = {2588-297X}, eissn = {2588-2988}, doi = {10.22060/ceej.2019.16118.6131}, abstract = {Temperature changes the engineering behavior of clay soils. Clay soils are used as a protective cover for burial of high-level wastes (HLWs), where the soil is exposed to medium to high temperature regimes. Marls are a type of sedimentary deposits consisting of clay minerals and calcium carbonate. These two components can substantially influence the behavior of marl soils from an engineering standpoint. The present study focuses on the engineering characteristics of marl soils under various temperature regimes with an emphasis on the microstructural changes in permeability coefficient, settlement, and compressive strength Therefore, after determining the geotechnical properties of the marl soil, its samples were exposed to temperatures from 25°C to 900°C. The changes in marl soil properties were analyzed via mechanical tests (measuring permeability, consolidation, and uniaxial compressive strength), and microstructural tests (measuring pH and X-Ray diffraction), and scanning electron microscopy (SEM). The microstructural analysis of marl soil samples indicates that due to the deterioration and formation of new minerals as well as soil particle arrangement and microscopic texture; temperature regimes increase the permeability coefficient. However, at 700 °C the formation of cement compounds reduces permeability coefficient by an approximate factor of 50,000.}, keywords = {Marl,Permeability Coefficient,Settlement,XRD,SEM}, title_fa = {مطالعه‌ی تغییرات ضریب نفوذپذیری و میزان نشست پذیری خاک‌های مارنی در اثر اعمال حرارت از دیدگاه ریزساختاری}, abstract_fa = {حرارت سبب ایجاد تغییرات در رفتار مهندسی خاک‌های رسی می‌شود. استفاده از خاک‌های رسی به عنوان پوشش محافظ در دفن زباله‌های سطح بالا از جمله مواردی است که رس تحت رژیم‌های حرارتی متوسط تا زیاد قرار می‌گیرد. مارن‌ها از جمله نهشته‌های رسوبی هستند که از کانی‌های رسی و کربنات کلسیم تشکیل شده‌اند. وجود کانی‌های رسی و کربنات کلسیم در خاک‌های مارن به شدت در رفتار مهندسی خا ک‌ها تأثیرگذار است. پژوهش حاضر به مطالعه خصوصیات مهندسی خاک های مارنی تحت رژیم‌های حرارتی با نگرش ویژه به تغییرات ضریب نفوذپذیری، نشست پذیری و مقاومت فشاری از منظر ریز ساختاری می‌پردازد. در این راستا پس از تعیین خصوصیات ژئوتکنیکی خاک مارن، نمونه‌های خاک در معرض سطوح حرارتی بین °C ۲۵ تا °C 9۰۰ قرار داده شده است. تغییر مشخصات خاک‌های مارنی در اثر اعمال حرارت از طریق انجام آزمایش‌های مختلف مکانیکی (نفوذپذیری، تحکیم، مقاومت فشاری محدود نشده (UCS ))و آزمایش‌های ریزساختاری (pH ،پراش اشعه ایکس (XRD )و تصویر میکروسکوپ الکترونی روبشی (SEM ))تجزیه و تحلیل شد. پایش ریزساختار خاک‌های مارنی نشان می‌دهد که به دلیل تخریب و شکل‌گیری کانی‌های جدید و همچنین آرایش ذرات خاک و بافت میکروسکوپی تحت رژیم‌های حرارتی، ضریب نفوذپذیری روند افزایشی دارد به نحوی که در دمای °C 500 میزان ضریب نفوذپذیری حدود 245 برابر فزایش یافته است اما در دمای °C 700 بـه دلـیـل تـشـکیل ترکیبات سیمانی ضریب نفوذپذیری حدود 85% کاهش می‌یابد. شایان ذکر است با افزایش اعمال حرارت در حالی که میزان تخلخل روند صعودی دارد اما میزان نشست پذیری کاهش می‌یابد.}, keywords_fa = {مارن,حرارت,ضریب نفوذپذیری,XRD,SEM}, url = {https://ceej.aut.ac.ir/article_3607.html}, eprint = {https://ceej.aut.ac.ir/article_3607_bf3af80bede414cb15457c177e94d0ad.pdf} } @article { author = {Teimourey, Reza and Dehghani, Amir Ahmad}, title = {Assessment of bed load transport formula by using developed applied software (STE) (Case study: Chehel-chai,Khormaloo and Soosara rivers in Golestan province)}, journal = {Amirkabir Journal of Civil Engineering}, volume = {52}, number = {11}, pages = {2743-2760}, year = {2021}, publisher = {Amirkabir University of Technology}, issn = {2588-297X}, eissn = {2588-2988}, doi = {10.22060/ceej.2019.16122.6132}, abstract = {Accurate estimation of flow and sediment discharges, as basic information, is important for many river engineering projects. To estimate bed load in the rivers, many experimental and semi-experimental equations have been developed but depending on the hydraulic conditions and sediment characteristics in each river, some of these equations may yield better results than the others. In this study, by developing an applied software, the abilities of 27 available equations for estimating bed load transport in rivers of Golestan province (Chehel-Chay, Khormaloo and Soosra), in which bed load is measured, have been evaluated. It should be noted that in this developed software quasi-two[1]dimensional models also can be used for computing velocity and sediment load distribution in cross section of the river. The software is also able to increase the accuracy of estimations by calculating calibration coefficients in the studied river. The results showed that by using the developed software, the best method for estimating bed load in the studied rivers is Yang’s method. In this case, the percentage of discrepancy ratio between 0.5 to 2 for the rivers Chehel-Chay, Khormaloo and Soosra is 43.8%, 50% and 30.8% respectively. Also, using quasi-two-dimensional models, increases percentage of discrepancy ratio between 0.5 to 2 for the rivers Chehel-Chay, Khormaloo and Soosra by 6.3%, 6% and 8%, respectively. The results also showed that by calculating and applying a calibration coefficient, accuracy of methods can be improved for the studied rivers.}, keywords = {Quasi-Two-dimensional model,Empirical sediment transport formulae,bed load,Sediment transport Estimators,Assessment of bed load estimators}, title_fa = {ارزیابی معادلات برآورد بار بستر در رودخانه‌های استان گلستان با استفاده از نرم افزار توسعه یافته STE}, abstract_fa = {تخمین مناسب دبی جریان و رسوب در رودخانه‌ها به عنوان اطلاعات پایه برای بسیاری از طرح‌ها و پروژه‌های مهندسی رودخانه دارای اهمیت است. برای محاسبه بار بستر در رودخانه‌ها، روابط تجربی و نیمه‌تجربی زیادی توسعه یافته‌اند که بسته به شرایط هیدرولیکی و مشخصات رسوب در هر رودخانه، ممکن است برخی از این روابط نتایج بهتری ارایه نمایند. در این تحقیق با توسعه یک نرم افزار کاربر پسند، توانایی 27 رابطه موجود در برآورد بار بستر رودخانه‌های استان گلستان (چهل چای، خرمالو و سوسرا) که در آنها بار بستر اندازه‌گیری می‌شود، مورد ارزیابی قرار گرفته است. لازم بذکر است که در این نرم‌افزار قابلیت استفاده از مدل‌های شبه دو بعدی در محاسبه توزیع عرضی سرعت و استفاده در روابط بار رسوبی نیز وجود دارد. همچنین این نرم‌افزار قادر به افزایش دقت محاسبات بار رسوبی با محاسبه ضرایب کالیبراسیون در رودخانه مورد مطالعه می‌باشد. نتایج نشان داد که با استفاده از نرم‌افزار توسعه یافته، بهترین روش برای برآورد بار بستر در رودخانه‌های مورد مطالعه با استفاده از روابط تجربی و نیمه تجربی موجود، روش یانگ می‌باشد. در این حالت فراوانی نسبت ناجوری بین نیم تا دو برای رودخانه‌های چهل‌چای، خرمالو و سوسرا بترتیب 43/8 ،50 و30/8 می‌باشد. همچنین با استفاده از مدل‌های شبه دو بعدی، نسبت ناجوری بین نیم تا دو برای رودخانه‌های چهل‌چای، خرمالو و سوسرا، بترتیب 6/3 ، 6 و 8 درصد افزایش می‌یابد. نتایج همچنین نشان داد که با استفاده از یک ضریب کالیبراسیون می‌توان دقت تعداد زیادی از روش‌ها در رودخانه‌های مورد مطالعه را افزایش داد.}, keywords_fa = {مدل ریاضی شبه دوبعدی,ظرفیت انتقال رسوب,روابط تجربی رسوبی,حمل رسوب,بار کف}, url = {https://ceej.aut.ac.ir/article_3550.html}, eprint = {https://ceej.aut.ac.ir/article_3550_c1269f4d3d5f59d96e4b7c514baf8353.pdf} } @article { author = {madani, bahareh and Behnamfar, Farhad}, title = {Parametric Study of Structure-Soil-Structure Interaction in Time and Frequency Domains}, journal = {Amirkabir Journal of Civil Engineering}, volume = {52}, number = {11}, pages = {2761-2778}, year = {2021}, publisher = {Amirkabir University of Technology}, issn = {2588-297X}, eissn = {2588-2988}, doi = {10.22060/ceej.2019.16156.6143}, abstract = {In this paper, focusing on structure-soil-structure interaction, dynamic behavior of two adjacent structures with flexible base is studied. The main identifiers of this structure-soil-structure interaction system are defined with dimensionless parameters. With considering a logical range of the parameters, various states including most practical cases are calculated. Soil flexibility and dynamic correlation between two adjacent structures through the soil are accounted for using springs and dashpots at the base of the structures. The equations of motion are solved in time and frequency domains for two adjacent single degree of freedom systems to make it possible to study parametrically the effect of structure-soil-structure interaction on the responses. As a result of harmonic analysis, natural frequencies with and without considering damping, damping ratios and amplitude of the system’s dynamic responses are calculated and compared with those of the single building (no adjacency). Also, the cases prone to a possible pounding are recognized. By analyzing such a system in both time and frequency domain, it is shown that with appropriate arrangements, both of the analysis procedures result in the same responses for an interaction problem.}, keywords = {adjacent structures,Soil-structure interaction,structure-soil-structure interaction,Natural frequency,Damping Ratio}, title_fa = {مطالعه‌ی پارامتری اندرکنش سازه-خاک-سازه در حوزه‌های زمان و فرکانس}, abstract_fa = {در این مقاله، با تمرکز بر تحلیل اندرکنش سازه-خاک-سازه، رفتار دینامیکی همزمان دو سازه ی مجاور و متکی بر بستر انعطاف پذیر مورد مطالعه قرار گرفته است. شاخص‌های اصلی معرف این سیستم سازه -خاک-سازه به صورت چند پارامتر بی بعد معرفی و درنظر گرفته شده و با منظور کردن بازه‌ای منطقی از مقادیر، حالات متنوعی شامل اغلب موارد عملی ممکن محاسبه گردیده است. انعطاف پذیری خاک و همبستگی دینامیکی دو سازه از طریق خاک، با استفاده از تعبیه‌ی فنرها و میراگرهایی در تکیه گاه سازه اعمال شده و مورد بررسی قرار گرفته است. معادلات حرکت در حوزه های زمان و فرکانس برای دو سیستم یک درجه آزاد مجاور حل شده و از این طریق مطالعه پارامتری اثر اندرکنش سازه-خاک- سازه بر واکنش‌ها ممکن گردیده است. در نتیجه‌ی تحلیل‌های دینامیکی هارمونیکی، فرکانس های طبیعی، نسبت‌های میرایی و دامنه ی واکنش دینامیکی سیستم محاسبه گردیده و با حالت عدم وجود سازه‌ی مجاور مقایسه گردیده است. همچنین حالات محتمل برای وقوع ضربه بین دو سازه‌ی مجاور تعیین شده است. در انجام تحلیل‌ها، کاربرد تحلیل در حوزه ی فرکانس و در حوزه ی زمان برای مطالعات فوق بررسی گردیده و نشان داده شده که با تمهیدات مناسب می‌توان از هر دو تحلیل به نتایج یکسانی از محاسبه اندرکنش بین سازه‌های مجاور دست یافت. در نتیجه، مشاهده شده که درنظر گرفتن اندرکنش متقابل در اغلب حالات منجر به افزایش فرکانس‌های طبیعی سیستم شده که به بیشترین افزایش مربوط به حرکت افقی پایه، تا بیش از %20 ،می‌باشد. از سوی دیگر، در مودهای مربوط به حرکت افقی روسازه تغییر فرکانس چندانی مشاهده نمی‌شود. همچنین، مجاورت تأثیر چندانی بر مشخصات دینامیکی ساختمان‌های کوتاه و سنگین ندارد، در حالیکه ساختمان بلند و سبک بیشتر تحت تأثیر مجاورت است طوریکه نسبت میرایی چنین سیستمی در حرکت گهواره‌ای تا دو و نیم برابر افزایش می‌یابد. اندرکنش متقابل سازه‌های سبک و بلند در خاکهای نرم تر موجب افزایش پاسخ سازه سخت تر تا حدود %40 و کاهش پاسخ سازه نرم تر تا حدود %15 می‌شود، اما روی خاک سخت پاسخ هر دو سازه کاهش می‌یابد که بیشینه تغییر، حدود %40 می‌باشد.}, keywords_fa = {سازه‌های مجاور,اندرکنش خاک-سازه,اندرکنش سازه-خاک-سازه,فرکانس‌های طبیعی,میرایی}, url = {https://ceej.aut.ac.ir/article_3730.html}, eprint = {https://ceej.aut.ac.ir/article_3730_cddd1f933cf11c4257bf680b1d4de07c.pdf} } @article { author = {Kamali, Arezoo and Mousavi, Seyed Roohollah and ghasemi, mohammadreza}, title = {Optimization of concrete tension stiffening model based on layered nonlinear analysis of FRP – RC beams}, journal = {Amirkabir Journal of Civil Engineering}, volume = {52}, number = {11}, pages = {2779-2794}, year = {2021}, publisher = {Amirkabir University of Technology}, issn = {2588-297X}, eissn = {2588-2988}, doi = {10.22060/ceej.2019.16440.6229}, abstract = {Tension stiffening effect, which is due to participation of concrete in resisting tension between cracks, results in the reduction of strains of reinforced concrete member relative to pure bars. In some researches, this effect was involved at strain – stress behavior of concrete after cracking that few researches investigated FRP reinforced concrete. In Present investigation, comparison of experimental data with results of layered nonlinear analysis of wide collection FRP-reinforced concrete beams relative to prior researches was used for extracting of concrete strain – stress after cracking. The resulting model unlike previous models was developed for all type of FRP bars. The constants of model are obtained from optimization method based on genetic. 78 curves from 87 curves of FRP – reinforced concrete beams under four-point bending are used for deriving of model coefficients and the others are used for investigating of optimal model. Furthermore, 20 percent of load – deflection data of 78 beams are also randomly selected for controlling of optimal model instead of developing of model. The average natural logarithm of experimental/calculated deflection ratios for randomly selected data by applying initial model and optimal model is 1.0457 and 0.2668, respectively. According to ideal value of zero for natural logarithm of experimental/calculated deflection ratio, applying optimal model has improved this statistical parameter by 74 percent. Responses of nonlinear analysis by using initial model and optimized model are compared with those of code relations.}, keywords = {deflection,Tension Stiffening,FRP Bars,Nonlinear Analysis,optimization}, title_fa = {بهینه سازی مدل سخت‌شوندگی کششی بتن براساس تحلیل غیرخطی لایه‌ای تیرهای بتنی مسلح شده با میلگردهای FRP}, abstract_fa = {اثر سخت شوندگی کششی که ناشی از مشارکت بتن بین ترک‌ها در تحمل کشش است، منجر به کاهش کرنش‌های عضو بتن مسلح نسبت به کرنش میلگردها به تنهایی می‌شود. در برخی پیشنهادها، این اثر در رفتار تنش- کرنش بتن بعد از ترک‌خوردگی گنجانده شده است که تعداد اندکی از آنها بتن با مسلح کننده‌های FRP را بررسی کرده‌اند. در ً گستردهای از تیرهای بتنی این تحقیق از مقایسه نتایج تحلیل غیرخطی لایه‌ای و نتایج آزمایشگاهی مجموعه‌ی نسبتا مسلح شده با میلگردهای FRP نسبت به تحقیقات پیشین، برای استخراج رابطه‌ی تنش- کرنش بتن بعد از ترک‌خوردگی استفاده شده‌است. مدل به دست آمده برخلاف مدل‌های پیشین برای همه‌ی انواع میلگردهای FRP ارائه شده است. ثابت‌های مدل با کاربرد روش بهینه‌سازی ژنتیک به دست می‌آیند. از 87 نمودار بار- خیز آزمایشگاهی تیرهای بتنی مسلح شده با میلگردهای FRP تحت خمش چهارنقطه‌ای ، 78 نمودار برای استخراج ثابت‌های مدل و 9 نمودار برای بررسی مدل بهینه به دست آمده به کار می‌روند. علاوه براین 20 درصد از داده‌های 78 تیر درنظر گرفته شده برای استخراج مدل، به صورت تصادفی حذف شده و به جای محاسبه‌ی مدل در کنترل مدل به کار می‌روند. میانگین لگاریتم طبیعی نسبت خیز آزمایشگاهی به محاسباتی برای داده‌های انتخاب شده برای کنترل، با کاربرد مدل اولیه 1/0457و با کاربرد مدل بهینه 0/2668 است. با توجه به اینکه مقدار ایده‌آل لگاریتم نسبت خیز آزمایشگاهی به محاسباتی صفر است، کاربرد مدل بهینه این پارامتر آماری را 74 درصد بهبود داده است. نتایج تحلیل غیرخطی با مدل‌های اولیه و بهینه با روابط آیین‌نامه‌ای نیز مقایسه شده‌اند.}, keywords_fa = {خیز,سخت شوندگی کششی,میلگردهای FRP,تحلیل غیرخطی,بهینه سازی}, url = {https://ceej.aut.ac.ir/article_3683.html}, eprint = {https://ceej.aut.ac.ir/article_3683_2a02257c8d2a3e6dc7e290fc16f14b09.pdf} } @article { author = {Moradi, Golam and abbasi, sajjad and Abbasnejad, Alireza}, title = {Effect of Water-Soluble Polymers and Nanoparticles on Physical, Mechanical, and inflationary Properties of Clay}, journal = {Amirkabir Journal of Civil Engineering}, volume = {52}, number = {11}, pages = {2795-2808}, year = {2021}, publisher = {Amirkabir University of Technology}, issn = {2588-297X}, eissn = {2588-2988}, doi = {10.22060/ceej.2019.16472.6242}, abstract = {In the present study, to investigate and compare the effect of Nanosilica nanoparticles and water-soluble polymer of cationic polyelectrolyte on a set of physical, mechanical and chemical properties of CL clay, a series of laboratory tests were performed on untreated soil samples, treated with Nanosilica and treated with cationic polyelectrolyte. Nanosilica was added to soil with 0.5, 1, 2 and 3% dry weight of soil and cationic polyelectrolyte with concentrations of 3, 6, 9 and 12 gr/liter based on optimum water content and their effects on the soil details have been investigated in 3,7,14 and 28 days of processing. Despite the differences in the effectiveness mechanisms, these materials showed similar effects on the variety of soil samples characteristics in this study. By adding of both materials to the soil, optimum water content, liquid limit, unconfined compressive strength, and water retaining potential of soil have been increased and Maximum dry density and free swelling percentage of soil decreased remarkably. On the other hand, regarding small changes of plastic limit and increasing of liquid limit, plasticity index increases. Also, for various amounts of additives, there is no significant change in soil pH.}, keywords = {Clay,Cationic polyelectrolyte,Nano-silica,Physical and Mechanical specifications,swelling}, title_fa = {بررسی و مقایسه‌ی تأثیر پلیمر‌های محلول در آب و نانوذرات بر خصوصیات فیزیکی، مکانیکی و تورم‌پذیری خاک رس}, abstract_fa = {بدون تردید یکی ازمقدماتی‌ترین ومهم‌ترین اصول در اجرای طرح‌های عمرانی،داشتن زمینی مقاوم برایاحداث بناست و لازمه‌ی آن وجود خاکی مناسب، با ویژگی‌های ژئوتکنیکی مطلوب در محل است. در سال‌های اخیر، تحقیقات گسترده‌ای در خصوص استفاده از مواد شیمیایی نوین از جمله پلیمر‌های شیمیایی و نانوذرات به منظور اصلاح خاک‌های ریزدانه صورت‌گرفته است. استفاده ازپلیمر‌های آلی در سالیان اخیراهمیت فراوانی یافته است واین پلیمر‌ها توانایی خودرا برای آنکه به عنوان ماده‌ی افزودنی جهت تثبیت خاک استفاده شوند، نشان داده‌اند. از سوی دیگردر سال‌هایاخیرگام‌های بزرگی در زمینه فناوری نانوبرداشته شده است و پیشرفت‌های فراوانی مبتنی برفناوری نانودر مهندسی ژئوتکنیک اتفاق افتاده است. در این مقاله از دو ماده نانوسیلیکا و پلی‌الکترولیت کاتیونی برای بهسازی و تثبیت خاک استفاده شده است، این مواد با درصد‌های مختلف به خاک اضافه شده و تأثیرآن‌ها برمشخصات خاک در زمان‌های عمل‌آوری 3 ،7 ،14 و 28 روزه موردبررسی قرار گرفته است. با افزایش هردو ماده به خاک درصد رطوبت بهینه، حد روانی، مقاومت فشاری محدود نشده و پتانسیل حفظ رطوبت خاک افزایش یافته و وزن مخصوص خشک حداکثر و درصد تورم آزاد نمونه‌های خاک کاهش نشان داده است، از سویی با توجه به تغییرات ناچیز حد خمیری، شاهد افزایش شاخص خمیری خاک نیزهستیم.}, keywords_fa = {خاک رس,پلی الکترولیت کاتیونی,نانوسیلیکا,مشخصات فیزیکی و مکانیکی,تورم و pH}, url = {https://ceej.aut.ac.ir/article_3632.html}, eprint = {https://ceej.aut.ac.ir/article_3632_eb7fb0e66c06358a5e776e9f47481142.pdf} } @article { author = {Saberi, Vahid and saberi, hamid and Sadeghi, Abbasali}, title = {Collapse Assessment of Steel Moment Frames Based on Development of Plastic Hinges}, journal = {Amirkabir Journal of Civil Engineering}, volume = {52}, number = {11}, pages = {2809-2830}, year = {2021}, publisher = {Amirkabir University of Technology}, issn = {2588-297X}, eissn = {2588-2988}, doi = {10.22060/ceej.2020.16177.6146}, abstract = {Building collapse is a level of the structure performance in which the amount of financial and life loss is maximized, so this event could be the worst incident in the construction. In this study, the collapse of low and mid-rise Regular special steel moment frames with 3, 6, and 9 story were designed by ETABS according to code guidelines and then the collapse of mentioned frames has been evaluated by nonlinear static pushover and incremental dynamic (IDA) analyses with SeismoStruct. The nonlinear static pushover analyses with three lateral load patterns were used to determine the likely location of the plastic hinges at the moment of probable failure mechanism for the mentioned frames and the nonlinear incremental dynamic analyses were used to assess the seismic intensities corresponding to form each failure mechanisms. Thus, the intensity of earthquake and the values of drift corresponding to the failure of studied frames were calculated. To perform nonlinear dynamic analyses, 10 far-fault records were used. The results of this study showed that the collapse of studied frames occurs under the far-fault records in different drifts and seismic intensities and the value of relative drift equivalent to the collapse limit varies from 2 to 5 percentage and It was also found that the collapse capacity of 3 and 6-story frames is 3.3 g and 3.4 g respectively in the uniform lateral load method and in 9-story frame, the collapse capacity of the first mode and linear lateral load methods is more and equals to 2.5 g.}, keywords = {Collapse,Plastic hinges,Special steel moment frame,Nonlinear Analyses,Far-fault record}, title_fa = {ارزیابی فروریزش قاب های خمشی فولادی بر اساس توسعه ی مفاصل پلاستیک}, abstract_fa = {فروریزش ساختمان سطحی از عملکرد سازه است که در آن میزان صدمات جانی و مالی به حداکثر خود می‌رسد، لذا این رخداد می‌تواند ناگوارترین حادثه در صنعت ساخت‌وساز باشد. در این تحقیق، سه قاب خمشی فولادی 3 ، 6 و 9 طبقه‌ی منظم با شکل‌پذیری ویژه بر اساس ضوابط آیین‌نامه‌ای با استفاده از نرم‌افزار ETABS طراحی و سپس فروریزش قاب های مذکور توسط تحلیل های غیرخطی استاتیکی بار افزون و دینامیکی افزایشی (IDA )با استفاده از نرم افزار SeismoStruct مورد ارزیابی قرارگرفته است. از تحلیل‌های غیرخطی بار افزون با سه الگوی مختلف بار جانبی به منظور تعیین موقعیت محتمل مفاصل پلاستیک در لحظه‌ی فروریزش استفاده شده است تا بتوان با بهره‌گیری از آنها، مکانیسم‌های خرابی محتمل قاب‌های مذکور را مشخص نمود و از تحلیل‌های دینامیکی غیرخطی افزایشی به منظور ارزیابی شدت‌های لرزه‌ای متناظر با شکل‌گیری هر یک از مکانیسم‌های خرابی استفاده شده است. بدین ترتیب، شدت زلزله و مقادیر پاسخ دریفت متناظر با فروریزش قاب‌های موردمطالعه محاسبه گردیده و برای انجام تحلیل‌های دینامیکی غیرخطی از 10 رکورد حوزه‌ی دور از گسل استفاده شده است. نتایج این تحقیق نشان می‌دهد که فروریزش قاب‌های موردمطالعه تحت رکوردهای دور از گسل در دریفت‌ها و شدت‌های لرزه‌ای مختلف رخ می‌دهد و مقدار دریفت نسبی معادل حد فروریزش بین 2 تا 5 درصد متغیر است و همچنین مشخص شد که ظرفیت فروریزش در قاب‌های 3 و 6 طبقه در روش بار جانبی یکنواخت بیشتر و به ترتیب معادل g 3/3 و g 3/4 می‌باشد و در قاب 9 طبقه، ظرفیت فروریزش در روش‌های بار جانبی مد اول و خطی بیشتر و معادل g 5/2 است.}, keywords_fa = {فروریزش,مفاصل پلاستیک,قاب خمشی فولادی ویژه,تحلیل های غیرخطی,رکورد حوزه ی دور از گسل}, url = {https://ceej.aut.ac.ir/article_3772.html}, eprint = {https://ceej.aut.ac.ir/article_3772_27b51c147d59ce9bd2f379023611b18c.pdf} } @article { author = {ouria, ahad and Emami, Sabah and Karamzadegan, Saeed}, title = {Laboratory Investigation of the Effect of the Cement Treatment of the Interface and the Thicknesses of Reinforcement on its Pull-out Capacity}, journal = {Amirkabir Journal of Civil Engineering}, volume = {52}, number = {11}, pages = {2831-2846}, year = {2021}, publisher = {Amirkabir University of Technology}, issn = {2588-297X}, eissn = {2588-2988}, doi = {10.22060/ceej.2019.16191.6149}, abstract = {Mechanical specification of the interface of soil and reinforcement is one of the most important parameters of the design and construction of reinforced soil systems. Anchorage length of the reinforcement is determined based on the soil-reinforcement interface parameters. Required long anchorage lengths restricts the application of reinforced soil systems. Improving the mechanical parameters of the soil-reinforcement interface could be used to develop the applications of reinforced soil structures in projects with limited space. In this research, the cement treatment of the interface of the soil and reinforcement was employed to improve the pull-out capacity of the reinforcement and consequently to reduce the anchorage length. The effect of the cement treatment on the pull-out capacity of the reinforcement was studied in the laboratory. Also, the effect of the increased thicknesses of the reinforcements resulted from the cemented layers adhered to the reinforcement surface was investigated. The laboratory tests conducted using specially developed pull-out test device. The tests conducted on high-strengths woven geotextiles with different thicknesses with both pristine and cement treated interfaces. Cement treatment carried out with 1.5 g/cm2 portland cement sprayed on water saturated geotextile. The results of tests conducted on pristine reinforcements with different thicknesses showed that increasing the thicknesses of the reinforcements increase the pull-out capacity. Also, the cement treatment increases the pull-out capacity of reinforcements. The results of this study show that cement treatment of the interface of soil and reinforcement increases the pull-out capacity of the reinforcement in two different mechanisms by increasing the thicknesses of the reinforcement and creating a rough surface on the reinforcement with higher interface friction angle.}, keywords = {Reinforced soil,pull-out,geotextile,cement treatment,Interface}, title_fa = {بررسی آزمایشگاهی اثر تثبیت سیمانی فصل مشترک خاک و ژئوتکستایل و ضخامت آن در مقاومت بیرون کشیدگی}, abstract_fa = {یکی از مهمترین پارامترهای تحلیل و طراحی سیستم‌های خاک مسلح، مشخصات مکانیکی فصل مشترک بین خاک و مسلح کننده است. مشخصات مکانیکی فصل مشترک، تعیین کننده طول مهاری مسلح کننده در این سیستم‌ها است. در بسیاری از موارد، بدلیل عدم امکان تامین طول مهاری مورد نیاز، استفاده از خاک مسلح با محدودیت روبرو می‌شود. تقویت مشخصات مکانیکی فصل مشترک خاک و مسلح کننده، می‌تواند دامنه کاربرد این روش تسلیح خاک را گسترده‌تر نماید. در این تحقیق، اثر ایجاد لایه سیمانی در فصل مشترک مسلح کننده و ماسه بعنوان روشی برای تقویت مقاومت بیرون کشیدگی مسلح کننده و کاهش طول مهاری مورد نیاز در طراحی‌ها، بصورت آزمایشگاهی بررسی شده است. با توجه به اینکه ایجاد لایه سیمانی باعث افزایش ضخامت مسلح کننده شد، تاثیر افزایش ضخامت مسلح کننده در مقاومت بیرون کشیدگی آن از خاک نیز بررسی شد. آزمایش‌ها در دستگاه مخصوص بیرون کشیدن مسلح کننده از خاک صورت گرفت. در این آزمایش‌ها، با قرار دادن لایه‌های ماسه در هر رویه مسلح کننده اشباع به همراه 1/5 گرم بر سانتی‌متر مربع سیمان و عمل آوری آن، دو لایه سیمانی در هر دو طرف مسلح کننده ایجاد گردید. نمونه‌های مسلح کننده با ضخامت‌های مختلف آزمایش شده و نتایج مقاومت بیرون کشیدگی آنها مقایسه گردید. نتایج این بررسی‌ها نشان داد که تثبیت سیمانی مسلح کننده‌ها باعث افزایش مقاومت بیرون کشیدگی آنها می‌شود. همچنین در مسلح کننده‌های مشابه، افزایش ضخامت مسلح کننده باعث افزایش مقاومت بیرون کشیدگی آنها می‌شود.}, keywords_fa = {خاک مسلح,مقاومت بیرون کشیدگی,ژئوتکستایل,تثبیت سیمانی,فصل مشترک خاک و ژئو تکستایل}, url = {https://ceej.aut.ac.ir/article_3650.html}, eprint = {https://ceej.aut.ac.ir/article_3650_f07fb13a93106fc49e692ea222377239.pdf} } @article { author = {Jafari Sahnehsaraei, Mohammad Ali and Rezazadeh Baghaal, Salman}, title = {Characterization of Ice and Concurrent Wind for Loading of Transmission Line Structures in Iran}, journal = {Amirkabir Journal of Civil Engineering}, volume = {52}, number = {11}, pages = {2847-2866}, year = {2021}, publisher = {Amirkabir University of Technology}, issn = {2588-297X}, eissn = {2588-2988}, doi = {10.22060/ceej.2019.16450.6232}, abstract = {In this paper, the parameters required for the ice and concurrent wind loading case, including the radial equivalent ice thickness and the concurrent wind speed for the return periods in the structures of the power transmission lines, are determined according to the standard criteria of IEC 60826. Loading parameters have been calculated using two-variable hazard curves and compared with simplified methods in IEC 60826. Ice and concurrent wind hazard curves are prepared using data recorded in 15 selected meteorological stations in the cold regions of the country (including heavy and ultra- heavy areas according to the climate-zoning map of the transmission lines). Numerical simulations (CRREL model for Freezing Rain and Cylindrical Growth of Wet Snow Sleeves model for Wet Snow) have been used to determine the thickness of ice formed around the conductor of the transmission lines due to the lack of direct data from the measurement. The results show significant conservatism of the reduction factors of the ice and concurrent wind in IEC 60826 standards at most of the studied meteorological stations. Accordingly, using the ice and wind hazard curves at the stations, the reduction factors are determined and presented to calculate the values of loading parameters in ice and wind loading case in terms of their reference values (which are available in the zoning maps). The proposed reduction factors are consistent with the standards of IEC 60826 and are suitable for use in loading and designing the structures of transmission lines with different return periods in the cold regions of the country.}, keywords = {Power Transmission Line,Ice with Concurrent wind,Loading,Transmission Towers,return period}, title_fa = {تعیین مشخصات یخ و باد همزمان برای بارگذاری سازه‌های خطوط انتقال نیرو در کشور}, abstract_fa = {در این مقاله، متغیرهای مورد نیاز برای حالت بارگذاری یخ و باد همزمان شامل ضخامت یخ معادل شعاعی و سرعت باد همزمان با آن به ازای دوره‌های بازگشت معین در سازه‌های خطوط انتقال نیرو، منطبق بر معیارهای استاندارد 60826 IECتعیین و ارائه شده‌اند. متغیرهای بارگذاری مورد نظر با استفاده از تهیه منحنی‌های خطر دو متغیره، ارائه و با روش‌های ساده شده در استاندارد 60826 IECمقایسه شده‌اند. منحنی‌های خطر یخ و باد همزمان با استفاده از داده‌های ثبت شده در 15 عدد از ایستگاه‌های هواشناسی منتخب در مناطق سردسیر کشور (شامل مناطق سنگین و فوق‌سنگین طبق نقشه پهنه‌بندی آب و هوایی خطوط انتقال) تهیه شده‌اند. برای تعیین ضخامت یخ تشکیل شده حول هادی خطوط انتقال با توجه به فقدان داده‌های مستقیم حاصل از اندازه‌گیری آن، از شبیه‌سازی عددی با مدل کریل برای باران یخی و مدل گسترش استوانه‌ای برف مرطوب برای برف مرطوب، استفاده شده است. نتایج حاصله نشان‌دهنده محافظه‌کاری قابل توجه ضرایب کاهشی یخ و باد همزمان ارائه شده در استاندارد 60826 IECدر اغلب ایستگاه‌های هواشناسی مورد مطالعه هستند. بر این اساس، با استفاده از منحنی‌های خطر یخ و باد همزمان در ایستگاه‌های مورد نظر، مقادیر ضرایب کاهشی جهت تعیین مقادیر متغیرهای بارگذاری در حالت یخ و باد همزمان بر حسب مقادیر مرجع آنها (که در نقشه‌های پهنه‌بندی موجودند)، تعیین و ارائه شده‌اند. ضرایب کاهشی ارائه شده سازگار با معیارهای استاندارد 60826 IEC بوده و برای بارگذاری و طراحی سازه‌های خطوط انتقال با دوره‌های بازگشت مختلف در مناطق سردسیر کشور، قابل استفاده هستند.}, keywords_fa = {خطوط انتقال نیرو,یخ و باد همزمان,بارگذاری,دکل‌های انتقال نیرو,دوره بازگشت}, url = {https://ceej.aut.ac.ir/article_3692.html}, eprint = {https://ceej.aut.ac.ir/article_3692_7c28f7b527ddd2eae8a12baeca7f2c9f.pdf} } @article { author = {hoseini, seyed omid and hosseinaei, saeed and ghasemi, mohamd}, title = {Investigation the behavior of concrete-covered steel columns and retrofitting it with carbon polymer fibers under simultaneous axial loading and reciprocating lateral loading}, journal = {Amirkabir Journal of Civil Engineering}, volume = {52}, number = {11}, pages = {2867-2886}, year = {2021}, publisher = {Amirkabir University of Technology}, issn = {2588-297X}, eissn = {2588-2988}, doi = {10.22060/ceej.2019.16429.6241}, abstract = {The application of composite sections in recent years is increasing because of its great advantages in advanced countries.The purpose of this study is to investigate the effective parameters on loading capacity of steel columns covered with concrete under the simultaneous impact of axial and cyclic lateral loading, including steel compound shape, concrete strength and retrofit with carbon polymer fibers. The use of a concrete-covered steel column in comparison to a single steel column or reinforced concrete column will increase the capacity of the final capacity significantly. In other words, composite columns have a very high load capacity. for this purpose, in order to study the behavior of steel columns covered with concrete under the simultaneous effect of axial and cyclic lateral loading, After validating the modeling in abaqus finite element software, the behavior of these columns in different cases of steel composite section, 28 day compressive resistance of a different concrete, and impact of retrofitting with carbon polymer fibers on ultimate capacity, is investigated. The results show that the parameters such as the shape and dimensions of section of steel column, the 28 - day compressive resistance of a different concrete and retrofitting with carbon polymer fibers have a significant effect on increasing or decreasing the ultimate capacity of these columns.}, keywords = {steel column covered with concrete,axial loading,cyclic lateral loading,Retrofitting,capacity}, title_fa = {بررسی رفتار ستون های فولادی پوشیده شده با بتن و مقاوم سازی آن با الیاف پلیمری کربن تحت اثر همزمان بارگذاری محوری و بارگذاری جانبی رفت و برگشتی}, abstract_fa = {کاربرد مقاطع مرکب در سالیان اخیر به علت محاسن فروان آن ها در کشورهای پیشرفته رو به افزایش است. علیرغم استفاده گسترده از مقاطع مرکب در دهه‌های اخیر، کماکان از لحاظ طراحی به این قاب‌ها همانند قاب های بتن آرمه و فولادی نگریسته می‌شود، از سهم همکاری توام بتن و فولاد چشم پوشی می‌گردد و بررسی رفتار شکل‌پذیری آن‌ها با کاستی‌هایی همراه است. استفاده موثر و کارآمد از قاب‌های مرکب نیازمند نگرشی متفاوت به قاب‌های بتنی و فولادی برای ورود به پروسه طراحی این نوع از قاب‌ها می‌باشد. از آنجا که انجام آزمایش برای بررسی هر مسئله امری زمان بر و پرهزینه است، استفاده از شبیه‌سازی ابزاری مناسب می‌باشد. هدف از این تحقیق بررسی پارامترهای موثر بر ظرفیت باربری ستون های فولادی پوشیده شده با بتن تحت اثر همزمان بارگذاری محوری و جانبی چرخه‌ای شامل شکل مقطع فولادی، مقاومت بتن و مقاوم سازی با الیاف پلیمری کربن است. استفاده از ستون فولادی پوشیده شده با بتن در مقایسه با ستون فولادی تنها و یا ستون بتن مسلح باعث افزایش ظرفیت چشم گیری در ظرفیت نهایی می‌شود، به عبارت دیگر ستون‌های مرکب از ظرفیت بار بسیار بالایی برخوردار می‌باشند. بدین منظور جهت بررسی رفتار ستون‌های فولادی پوشیده شده با بتن تحت اثر همزمان بارگذاری محوری و جانبی چرخه‌ای پس از صحت سنجی مدل‌سازی در نرم‌افزار اجزای محدود آباکوس به بررسی رفتار این ستون‌ها در حالات مختلف سطح مقطع فولاد، مقاومت فشاری 28 روزه بتن متفاوت و مقاوم‌سازی با الیاف پلیمری کربن بر ظرفیت نهایی آن پرداخته شده است. نتایج تحقیق نشان می‌دهد پارامترهایی همچون شکل و ابعاد سطح مقطع ستون فولادی، مقاومت فشاری 28 روزه بتن و مقاوم سازی با الیاف پلیمری کربن تاثیر به سزایی در افزایش یا کاهش ظرفیت نهایی این ستون ها دارد. در نهایت به بررسی الگوی ترک خوردگی در بتن پرداخته شده است و با توجه به الگوی گسترش ترک، مقاوم سازی با الیاف پلیمری کربن بر روی سطح بتن برای کاهش ترک خوردگی انجام شده است.}, keywords_fa = {ستون فولادی پوشیده شده با بتن,بارگذاری محوری,بارگذاری جانبی چرخه ای,مقاوم سازی}, url = {https://ceej.aut.ac.ir/article_3557.html}, eprint = {https://ceej.aut.ac.ir/article_3557_90f71402f8976c2c80dc224086a08bbf.pdf} } @article { author = {Sarvari, Saeed and esfahani, mohammad Reza}, title = {An experimental study on post-punching behavior of flat slabs to prevent progressive collapse}, journal = {Amirkabir Journal of Civil Engineering}, volume = {52}, number = {11}, pages = {2887-2898}, year = {2021}, publisher = {Amirkabir University of Technology}, issn = {2588-297X}, eissn = {2588-2988}, doi = {10.22060/ceej.2019.16471.6245}, abstract = {If unpredictable loads are applied to the flat slab-column connections, punching shear failure occurs with almost no warning signs. According to the brittle manner of this failure, the load carried by the slab-column connection redistributes to adjacent supports and causes overloading to these supports. Due to this overloading and brittle nature of punching shear failure, progressive collapse may happen both horizontally or vertically. In order to prevent the progressive collapse of flat slab-column connections, it is necessary to provide a secondary load carrying mechanism after punching shear. In this Paper, Suggestions for establishing a supporting mechanism in the flat slab connections after punching failure are proposed. For this purpose, an experimental study was performed to investigate the postpunching behavior of 9 slab specimens with various reinforcement layouts and concrete covers. The effects of integrity, compressive and bent-up reinforcements, diameter of tensile reinforcements, and concrete cover of tensile reinforcements on the post-punching behavior of slab-column connections were studied. The results of the experiments show that the integrity reinforcements significantly improve the post-punching strength. The compressive reinforcements may not increase post-punching strength. The increase of the concrete cover of the tensile reinforcements and decrease of the diameter of the tensile reinforcement result in an increase of the post-punching strength. The bent-up reinforcement increases the punching and post-punching strengths, simultaneously.}, keywords = {Post-Punching strength,Flat slab,Progressive Collapse,Integrity reinforcement,Punching shear failure}, title_fa = {بررسی رفتار دال های تخت پس از برش پانچینگ برای جلوگیری از تخریب پیشرونده}, abstract_fa = {چنانچه در اتصال دال تخت به ستون تحت اثر بارهای غیرقابل پیش‌بینی، گسیختگی پانچینگ رخ دهد، بنا به ماهیت ترد این گسیختگی پس از بازتوزیع نیروها در اتصالات مجاور، ممکن است تخریب پیشرونده به صورت افقی یا قائم رخ دهد. جهت پیشگیری از تخریب پیشرونده و گسیختگی ترد و بدون اخطار اتصال دال به ستون، ایجاد یک سازوکار پشتیبان پس از گسیختگی پانچینگ و بازتوزیع در اتصال یادشده، ضروری به نظر می‌رسد. در این تحقیق راهکارهای برقراری یک سازوکار پشتیبان در اتصال دال تخت به ستون پس از برش پانچینگ از طریق پیشنهاد تغییراتی در آرماتور و بتن بررسی می‌گردد. 9 نمونه دال مربعی با ابعاد 1600 میلی‌متر و ضخامت‌های 125( 7 نمونه)، 135( 1 نمونه) و 145( 1 نمونه) میلی‌متر با جزئیات متفاوت در آرماتور گذاری بر روی تکیه‌گاه‌های ساده مورد آزمایش قرار گرفت. در این پژوهش اثرات آرماتورهای یکپارچگی )آرماتورهای عبوری از ستون در بخش فشاری)، آرماتورهای فشاری، قطر آرماتور کششی، پوشش بتن آرماتورهای کششی و آرماتورهای یکپارچگی خمشده به بالا بر روی مقاومت پس پانچینگ بررسی گردیده است. نتایج آزمایش‌ها نشانگر آن است که با افزودن آرماتور یکپارچگی مقاومت پس پانچینگ افزایش یافته و با افزودن آرماتورهای فشاری در ناحیه ستونی دال تخت افزایش چشمگیری در مقاومت‌های یادشده اتفاق نمی‌افتد. افزایش پوشش بتن در ناحیه کششی باعث افزایش مقاومت پانچینگ و پس پانچینگ به‌طور همزمان می‌گردد. با کاهش قطر آرماتور کششی، مقاومت پس پانچینگ افزایش می‌یابد. خم کردن آرماتور یکپارچگی به سمت ناحیه کششی دال، باعث افزایش مقاومت پانچینگ و پس پانچینگ اولیه خواهد شد.}, keywords_fa = {مقاومت پس پانچینگ,دال تخت,تخریب پیشرونده,آرماتور یکپارچگی,گسیختگی پانچینگ}, url = {https://ceej.aut.ac.ir/article_3536.html}, eprint = {https://ceej.aut.ac.ir/article_3536_f37b46006cc36c5e8669df22479659b6.pdf} } @article { author = {hasanzadeh, ahmadreza and biglari fadafan, ali and Mousavi, Seyyed Yasin and tabarsa, alireza}, title = {Evaluation of Resistance Parameters of Fine-Grained Soil Containing Nano-Lime}, journal = {Amirkabir Journal of Civil Engineering}, volume = {52}, number = {11}, pages = {2899-2912}, year = {2021}, publisher = {Amirkabir University of Technology}, issn = {2588-297X}, eissn = {2588-2988}, doi = {10.22060/ceej.2019.16198.6152}, abstract = {Nowadays, soil stabilization has a vital importance due to the population growth, the necessity of construction and natural unsuitability of soil for construction. The use of additives such as lime and cement are one of the ways that can be applied for soil stabilization. Among new additives for soil stabilization, it can be pointed out that Nano-Material is a more efficient and cost-effective method with respect to traditional additives. One of this Nano-Material is Nano-Lime that can be used for soil improvement. Therefore, in this research, the effect of Nano-Lime on soil resistance parameters was investigated. For this purpose, behavior of soil specimens containing 0.5, 1 and 2% Nano-Lime that is investigated under unconsolidated undrained triaxial after 7, 14 and 28 days curing. According to the results, the values of maximum deviator stress are increased by adding Nano-Lime to the soil specimens, and this trend raises by increasing percentage of Nano-Lime in the soil and curing days. That said, the 28-days maximum deviator stress of clean soil is increased by 21.3 to 38.3%, 27.0 to 59.3% and 29.6 to 70.8% with including 0.5%, 1% and 2% Nano-Lime for cell pressure 100, 200 and 300 kPa, respectively. Moreover, it can be seen that both cohesion and stiffness of specimens containing Nano-Lime is raised by increasing percentage of Nano-Lime in the soil and curing days. }, keywords = {Nano-Lime,Triaxial,Stress-Strain curve,stiffness,Cohesion}, title_fa = {ارزیابی مشخصه های مقاومتی خاک ریزدانه حاوی نانوآهک}, abstract_fa = {امروزه با توجه به رشد جمعیت، لزوم ساخت و ساز و مناسب نبودن خاک طبیعی موجود در محل برای احداث سازه، بهسازی خاک از اهمیت ویژه‌ای برخوردار شده است. یکی از روش‌های بهسازی استفاده از افزودنی‌هایی همچون آهک و سیمان در ارتقا کیفیت خاک می‌باشد. از افزودنی‌های نوین در جهت بهسازی خاک می‌توان به نانو مواد اشاره کرد که کارآمدتر و مقرون به صرفه‌تر از افزودنی‌های سنتی می‌باشند. نانو آهک از جمله نانو موادی می‌باشد که می‌تواند به منظور بهسازی خاک مورد استفاده قرار گیرد. از این رو در این پژوهش به بررسی اثر نانو آهک بر روی پارامترهای مقاومتی خاک پرداخته شد. بدین منظور نمونه خاک‌های حاوی 0/5 ،1 و 2 درصد وزنی خاک در سه سن عمل‌آوری 7 ،14 و 28 روز تحت آزمایش سه محوری تحکیم نیافته زهکشی نشده قرار گرفت. مطابق نتایج مقادیر بیشینه تنش انحرافی نمونه‌ها با افزودن نانو به خاک افزایش می‌یابد و این امر با افزایش درصد نانو آهک در خاک همچنین گذشت زمان عمل‌آوری فزونی می‌یابد. به این ترتیب که حضور 0/5 ،1 و 2 درصد نانوآهک در زمان عمل‌آوری 28 روز سبب افزایش بیشینه تنش انحرافی در محدوده 21/3 الی 38/3 ،27 الی 59/3 و 29/6 الی 8/ 70برای فشارهای همه‌جانبه 100 ،200 و 300 کیلوپاسکال می‌باشد. علاوه بر این در نمونه‌های حاوی نانو آهک نسبت به نمونه خاک تمیز افزایش سختی دیده شد. همچنین نتایج افزایش چسبندگی نمونه‌های خاک را تحت تاثیر نانو آهک نشان داد که این امر با گذشت زمان عمل‌آوری افزایش یافت.}, keywords_fa = {نانو آهک,آزمایش سه محوری,منحنی تنش-کرنش,سختی,چسبندگی}, url = {https://ceej.aut.ac.ir/article_3649.html}, eprint = {https://ceej.aut.ac.ir/article_3649_bc3c5421581fe25ff9ec33484e4b0c93.pdf} } @article { author = {mohamadali pourahari, amirali and Jalili-Ghazizadeh, Mohammadreza and attari, jalal and karimi, Mahmoud}, title = {A numerical study on the behavior of a supercritical flow over piano key side weirs}, journal = {Amirkabir Journal of Civil Engineering}, volume = {52}, number = {11}, pages = {2913-2930}, year = {2021}, publisher = {Amirkabir University of Technology}, issn = {2588-297X}, eissn = {2588-2988}, doi = {10.22060/ceej.2019.16228.6160}, abstract = {Side weirs are a type of hydraulic structures that can be utilized as a divert structure, controller and distributing flow discharge in Floods and high velocity flows. The flow type over these structures is spatially varied flow with decreasing discharge. Due to use of side weirs for transferring and discharge control in flood flows with high velocities, it is very likely to have a supercritical flow over side weirs. Piano key and labyrinth side weirs are used, where the weir opening length is limited. An advantage of these kind of side weirs is the weir’s effective length relative to its opening. The most carried out studies on the Piano key weirs are limited to the experimental investigations. Considering the limited conditions and high cost of the laboratory works in one hand and recent developments of the numerical models, on the other hand, it is necessary to use the well known fluid dynamics software to simulate the side weir flows. In this study side weirs with different plans have been simulated by FLOW[1]3D. The FLOW-3D numerical model has been calibrated and verified for simulating side weirs using the experimental results. In this study, discharge coefficient for piano key side weirs in supercritical flow is presented. To obtain an optimized shape of the piano key side weirs the different shapes of the keys are also compared. These These results this study can be used for design of the piano key side weirs.}, keywords = {Piano key weir,Side weir,Supercritical flow,Discharge Coefficient,numerical Model}, title_fa = {بررسی عددی رفتارجریان فوق بحرانی برروی سرریزهای جانبی کلیدپیانویی}, abstract_fa = {سرریزهای جانبی از جمله سازه‌های هیدرولیکی هستند که به عنوان یک سازه انحرافی می‌توانند به منظور کنترل و تقسیم دبی درجریان‌های سیلابی و با سرعت بالا، به کار گرفته شوند. جریان برروی این سازه‌ها از نوع متغیر مکانی و در حالت کاهش دبی است. باتوجه به بکارگیری سرریزهای جانبی در انتقال و کنترل دبی در جریان‌های سیلابی و مقادیر قابل توجه سرعت، وقوع جریان فوق بحرانی برروی سرریز جانبی بسیار محتمل است. هنگامی که طول دهانه سرریز محدود باشد می‌توان از سرریزهای جانبی کنگرهای و کلید پیانویی استفاده نمود. یکی از مزایای این سرریزها افزایش طول مؤثر سرریز نسبت به بازشدگی دهانه است. عمده مطالعات انجام شده در زمینه سرریزهای جانبی کلیدپیانویی محدود به روش آزمایشگاهی بوده، بنابراین با توجه به شرایط محدود آزمایشگاه هزینه زیاد انجام آنها و پیشرفت‌های اخیر در زمینه مدل‌های عددی، شبیه‌سازی این سرریز با نرم‌افزارهای دینامیک سیالات محاسباتی حائز اهمیت است. در این تحقیق سرریزهای جانبی با اشکال مختلف در پلان توسط نرم‌افزارFLOW-3D شبیه سازی شده است. ابتدا با نتایج آزمایش‌های موجود، مدل عددی  FLOW-3Dکالیبره و صحت سنجی برای شبیه‌سازی سرریزهای جانبی انجام شد. ازجمله نتایج بدست آمده در این تحقیق، تعیین و ارائه رابطه بین ضریب تصحیح انرژی جنبشی(α )وضریب تصحیح اندازه حرکت (β ،)تعیین و ارائه ضریب آبگذری برای سرریزهای جانبی کلیدپیانویی در جریان فوق بحرانی و همچنین مقایسه شکل سرریزهای کلیدپیانویی است. نتایج تحقیق حاضر می‌تواند در طراحی سرریزهای جانبی مورد استفاده قرار بگیرد}, keywords_fa = {سرریزکلیدپیانویی,سرریز جانبی,جریان‌فوق‌بحرانی,ضریب آبگذری,مدل‌ عددی}, url = {https://ceej.aut.ac.ir/article_3529.html}, eprint = {https://ceej.aut.ac.ir/article_3529_0f4608805d04e7af0ea76e23e708e211.pdf} } @article { author = {Imani, somaye and Farokhnia, Ashkan and morid, saeid and Roozbahani, Reza}, title = {Spatio-temporal Analysis of Temperature and Precipitation Trends in Tashk-Bakhtegan Watershed}, journal = {Amirkabir Journal of Civil Engineering}, volume = {52}, number = {11}, pages = {2931-2944}, year = {2021}, publisher = {Amirkabir University of Technology}, issn = {2588-297X}, eissn = {2588-2988}, doi = {10.22060/ceej.2019.16244.6168}, abstract = {In the present era, climate change and its impact on available water resources are one of the main challenges. In this regard, temporal and spatial analysis of temperature and precipitation, which are important parameters in determining the status of water resources, can be used to assess the hydro-climatological conditions of the watershed and appropriate management policies. In this research, the trend in precipitation and temperature distribution over 30 years testing period of 1981-2010 was investigated using non-parametric tests such as Man-Kendal, Spearman, Sen’s Slope, and Pettit. Afterward, interpolation techniques, such as IDW, LPI, GPI and RBF were used to detect spatially trends at the watershed. The results showed that precipitation decreased by 14.3% during the period 1981-2010 and the temperature increased by 3.5%, with changes in precipitation and temperature occurring in 2004 and 1985, respectively. However, the negative trend in precipitation was not significant in contrast to the positive temperature trend during the study period. A comparative analysis of interpolation techniques shows that Ordinary Kriging and Radial Basis Functions with least error are the best methods for spatial analysis of precipitation and temperature, respectively.}, keywords = {Temporal and spatial trends,Precipitation,Temperature,Tashk-bakhtegan Watershed,Interpolation}, title_fa = {بررسی روند تغییرات زمانی- مکانی دما و بارش در حوضه آبریز طشک-بختگان}, abstract_fa = {یکی از چالش‌های جدی در عصر حاضر تغییر اقلیم و تأثیر آن بر منابع آب در دسترس است. در این راستا بررسی تغییرات زمانی و مکانی بارندگی و دما، به عنوان پارامترهای تأثیرگذار بر وضعیت منابع آب، می‌تواند در ارزیابی شرایط هیدروکلیماتولوژی حوضه و اتخاذ سیاست‌های مدیریتی مناسب باشد. در این تحقیق ابتدا روند زمانی بارش و دما سالانه حوضه آبریز طشک-بختگان در یک دوره آماری 30 ساله (2010-1981 )با استفاده از روش‌های آماری غیرپارامتریک من- کندال، اسپیرمن، شیب سن و پتی بررسی شد. سپس برای درک تفاوت مکانی این پارامترها در سطح حوضه از تکنیک‌های درونیابی عکس فاصله (IDW ،)چندجمله‌ای محلی (LPI ،)چندجمله‌ای جهانی (GPI )و روش تابع و روش تابع شعاعی(RBF )مختلف استفاده شد. نتایج نشان داد بارندگی طی دوره 1981-2010 به میزان 14/3درصد کاهش و دما به میزان3/5 درصد افزایش داشته است که روند تغییرات برای بارش و دما به ترتیب در سال 2004 و 1985 اتفاق افتاده است. اما روند کاهش بارندگی در منطقه برخلاف افزایش دما معنی‌دار نیست. با این وجود، استفاده از روش کریجینگ برای بررسی تغییرات مکانی بارندگی و روش تابع شعاعی برای بررسی تغییرات مکانی دما در حوضه مورد مطالعه بدلیل کمترین خطای گزارش شده پیشنهاد می‌گردد. مقایسه تکنیک‌های درونیابی نیز نشان داد روش کریجینگ معمولی و توابع پایه شعاعی با حداقل خطا، بهترین روش برای تجزیه و تحلیل مکانی بارش و دما هستند.}, keywords_fa = {روند زمانی و مکانی,بارش,دما,حوضه آبریز طشک-بختگان,درونیابی}, url = {https://ceej.aut.ac.ir/article_3654.html}, eprint = {https://ceej.aut.ac.ir/article_3654_bf3d0fa189dfc4e208f3b8fad089c4ca.pdf} } @article { author = {DarvishNezhad Aliabad, Mahdi and Zandi, Yusef and DarvishNezhad Aliabad, Zahra}, title = {Evaluation of Mechanical Properties of Concrete Made with Metakaolin Scrap, Melting Iron Slag and Copper Smelting Slag}, journal = {Amirkabir Journal of Civil Engineering}, volume = {52}, number = {11}, pages = {2945-2962}, year = {2021}, publisher = {Amirkabir University of Technology}, issn = {2588-297X}, eissn = {2588-2988}, doi = {10.22060/ceej.2019.15623.6196}, abstract = {Concrete is the most important consumable in constructional construction, which is increasing. Cement is used as a constituent of concrete to produce it, and on the other hand it produces 8% of the world’s carbon dioxide produced. In this study, the mechanical properties and durability of concrete made with copper smelting slag, iron melt slag and metalaoleene as a substitute for cement have been investigated. A total of 384 samples were made up of 16 mixing designs with varying degrees of replacement of copper smelting slag, iron smelting, and metalaole waste. Mixing scheme According to the American ACI 211.1 regulations and the conditions for the SSD materials, dry aggregates then cement materials after that, and finally the supernatant, were gradually added to the mixture. On the designs in a fresh state, a slump test, and in a hardened condition at the age of 7, 14, 28, and 90 days, the compressive strength was tested according to standard BS 1881 and at 28 days of pressure test in accordance with DIN 1048-5. In all designs containing pozzolan, we see a decrease in water absorption compared to a pozzolan design. In, the constant percent displacement of water under pressure is related to the designs containing metalaole and the most related to the plans containing copper smelting slag.}, keywords = {Concrete technology,Mechanical Properties of Concrete,Metakaolin Scrap,Melting Iron Slag,Copper Smelting Slag}, title_fa = {ارزیابی مشخصات مکانیکی بتن‌های ساخته شده با ضایعات متاکائولن، سرباره‌ی ذوب آهن و سرباره‌ی ذوب مس}, abstract_fa = {بتن مهم‌ترین مصالح مصرفی در ساخت و سازهای عمرانی می‌باشد که استفاده از آن رو به افزایش است. سیمان به عنوان یکی از اجزای تشکیل دهنده بتن انرژی فراوانی برای تولید آن مصرف می‌شود و از سوی دیگر موجب تولید 8 درصد گازکربنیک تولید شده در جهان است. در تحقیق حاضر به بررسی خصوصیات مکانیکی و دوام بتن ساخته شده با پوزولان های سرباره ذوب مس، سرباره ذوب آهن و متاکائولن به عنوان جایگزین سیمان پرداخته شده است. تعداد 16 طرح اختلاط با درصدهای مختلف جایگزینی سرباره ذوب مس، سرباره ذوب آهن، ضایعات متاکائولن جمعا 384 نمونه ساخته SSD1 در نظر گرفته شده است، ابتدا سنگدانه شد. طرح اختلاط طبق آیین‌نامه آمریکا 1.211 ACIو شرایط مصالح‌های خشک سپس مواد سیمانی پس از آن آب و در نهایت محلول فوق روان کننده به تدریج به مخلوط اضافه شد. بر روی طرح‌ها در حالت تازه، آزمایش اسلامپ و در حالت سخت شده در سنین 7 ،14 ،28 و 90 روزه آزمایش مقاومت فشاری براساس استاندرد 1881 BSو در سن 28 روزه آزمایش نفوذ آب تحت فشار طبق 5-1048 DIN انجام گرفت. در تمامی طرح‌های حاوی پوزولان شاهد کاهش جذب آب در مقایسه با طرح بدون پوزولان هستیم. در، درصد ثابت جایگزینی نفوذ آب تحت فشار مربوط به طرح‌های حاوی متاکائولن و بیشترین مربوط به طرح‌های حاوی سرباره ذوب مس می‌باشد .}, keywords_fa = {تکنولوژی بتن,مشخصات مکانیکی بتن,ضایعات متاکائولن,سرباره ذوب آهن,سرباره ذوب مس}, url = {https://ceej.aut.ac.ir/article_3544.html}, eprint = {https://ceej.aut.ac.ir/article_3544_b8222e3324e72be4f4b3b35cfdfd76f9.pdf} }