@article { author = {Asghari, A.}, title = {Evaluation of Ductility Reduction Factor for X-braced Steel Frames Which are Braced in Two End spans}, journal = {Amirkabir Journal of Civil Engineering}, volume = {49}, number = {2}, pages = {213-226}, year = {2017}, publisher = {Amirkabir University of Technology}, issn = {2588-297X}, eissn = {2588-2988}, doi = {10.22060/ceej.2016.697}, abstract = {In this study, the ductility reduction factor of Ordinary Concentrically Braced Frames(OCBFs) and special concentrically braced frames (SCBFs) which are braced concentrically in two endsides of frames, is evaluated. The results confirmed that, using SCBFs will reduce about 15 to 45 percentof total used material for one to 16 story frames respectively. In addition, for all of the 16 ordinaryX-braced frames, which have 1 to 16 story height, calculated ductility reduction factor exceeds fromASCE7’s proposed one, except for 16 stories frame. For studied frames, which are braced in two endsides, using the X-bracing system, the results confirmed that ductility demand is achievable without anysignificant problem. In addition, results indicated that although the response modification factor which isproposed by Iranian seismic design code (2800 standard), is more logical than ASCE7’s one, for frameswhich are braced in the end sides, the response modification factor should be taken less than 5.5.}, keywords = {Ductility,Ductility reduction factor,Concentrically braced frame,pushover analysis,Target displacement}, title_fa = {ارزیابی ضریب کاهش شکل پذیری مهاربندهای ضربدری واقع در دو دهانه ابتدا و انتهای قاب های ساختمانی ساده}, abstract_fa = {در این تحقیق تلاش شده است ضریب کاهش شکل‌پذیری قاب‌های مهاربندی شده ضربدری معمولی و ویژه که در دو دهانه کناری قرار دارند، مورد ارزیابی قرار گیرد. بر اساس نتایج بدست آمده از این تحقیق، از نظر میزان مصالح مصرفی قاب‌های مهاربندی شده ضربدری ویژه و واقع در دو دهانه کناری نسبت به قاب‌های مهاربندی شده معمولی بترتیب برای قاب‌های یک تا شانزده طبقه از 15 الی 45 درصد مقرون به صرفه‌تر است. در شانزده قاب یک تا شانزده طبقه مهاربندی شده ضربدری معمولی به جز در قاب شانزده طبقه در بقیه قاب‌ها، ضریب کاهش شکل‌پذیری از مقدار مورد نظر آئین‌نامهASCE7 بیشتر بوده و در اینگونه قاب‌های مهاربندی شده ضربدری و واقع در دو دهانه کناری مشکلی از حیث تامین شکل‌پذیری مورد نیاز مشاهده نگردید. همچنین بر اساس نتایچ حاصله، با وجود اینکه ضریب رفتار پیشنهاد شده در پیش‌نویس استاندارد 2800 ایران برای قاب‌های مهاربندی شده همگرای ویژه منطقی‌تر از ضریب رفتار پیش‌بینی شده در آئین‌نامه ASCE7 است، لیکن مطابق نتایج بدست آمده از این تحقیق برای شانزده قاب مهاربندی شده ضربدری ویژه و واقع در دو دهانه کناری، ضریب رفتار باید کمتر از 5/5 در نظر گرفته شود.}, keywords_fa = {شکل پذیری,ضریب کاهش شکل پذیری,قا بهای مهاربندی شده همگرا,تحلیل پوش آور,تغییرمکان هدف}, url = {https://ceej.aut.ac.ir/article_697.html}, eprint = {https://ceej.aut.ac.ir/article_697_bf0028676b430515406a251292f19e67.pdf} } @article { author = {Mohammadi, M. and Gholami, Sepehr}, title = {A Proposed Method to Satisfy Code Drift Criteria to Achieve Building with Higher Seismic Performance}, journal = {Amirkabir Journal of Civil Engineering}, volume = {49}, number = {2}, pages = {227-236}, year = {2017}, publisher = {Amirkabir University of Technology}, issn = {2588-297X}, eissn = {2588-2988}, doi = {10.22060/ceej.2016.686}, abstract = {The first step in designing structures is choosing sufficient elements for the applied loads, including dead, live, wind and earthquake ones. Then, drifts of all stories are compared with allowable values and if required some structural elements are so resized to satisfy the drift criteria. The process of resizing is normally carried out by trial and error and relied mostly on engineering judgment. In other words, there are many approaches for satisfying the drift criteria, which some of them may lead to structures with poor seismic behavior. Moreover, based on Iranian Standard 2800, the designer is allowed to use analytical period of vibration in drift controlling process, instead on one calculated by the code proposed formula. In this study, a method is proposed to find the best elements for resizing and subsequently satisfying the drift controlling criteria. Furthermore, it is shown that applying the analytical period of vibration leads to structures with better seismic behavior. For the purposes, Endurance Time method is applied in which nonlinear behavior of slender special moment resisting frame steel structures and their damage indices are considered.}, keywords = {Drift,steel structure,Special moment resisting frame,damage index,Endurance time}, title_fa = {کنترل ضوابط محدودیت تغییر مکان جهت بهبود رفتار لرز های ساز هها}, abstract_fa = {امروزه روش معمول در طراحی ساختمان‌‌ به این صورت است که طراحی آن بر اساس بار‌های وارد و ضوابط نیرویی موجود در آیین‌نامه انجام می‌شود، سپس تغییر مکان طبقات سازه با مقادیر مجاز مقایسه می‌گردد و در صورت نیاز قسمت‌هایی از سازه تقویت می‌شود تا این ضوابط در همه طبقات برآورده شود. تا‌کنون ملاک خاصی برای یافتن مناسب‌ترین اعضایی که با تقویت آنها، این ضوابط به بهترین شکل ارضا شوند وجود ندارد و بنابر‌این به هنگام طراحی سازه روش‌های مختلفی برای ارضای ضوابط کنترل تغییر مکان به‌کار می‌رود که مطالعات گذشته نشان داده است اگرچه برخی از این روش‌ها منجر به ارضای ضوابط آیین‌نامه‌ می‌شود اما عملکرد لرزه ای سازه را با چالش مواجه نموده است. در این تحقیق راهکاری برای ارضای منطقی ضوابط کنترل تغییرمکان ارائه و در چند سازه فولادی قاب خمشی ویژه لاغر نشان داده شده است که راهکار ارائه شده نسبت به روش‌های موجود، به سازه با رفتار لرزه ای بهتر منجر می‌شود. برای مقایسه رفتار لرزه ای سازه‌های مورد مطالعه از تحلیل تاریخچه زمانی غیر‌خطی استفاده شد که ملاک مقایسه نیز شاخص خرابی و زمان دوام در نظر گرفته شده است.}, keywords_fa = {ضوابط کنترل تغییرمکان,قاب خمشی فولادی ویژه,شاخص خرابی,زمان دوام}, url = {https://ceej.aut.ac.ir/article_686.html}, eprint = {https://ceej.aut.ac.ir/article_686_a7111051fae635f3125de1a09e165fc3.pdf} } @article { author = {Ebadi, P. and Maghsoudi, A.}, title = {Case Study on Seismic Performance of Soft Stories in Short Steel Structures and Replacement of Braces with Equivalent Moment Resisting Frame}, journal = {Amirkabir Journal of Civil Engineering}, volume = {49}, number = {2}, pages = {237-250}, year = {2017}, publisher = {Amirkabir University of Technology}, issn = {2588-297X}, eissn = {2588-2988}, doi = {10.22060/ceej.2015.408}, abstract = {Many of changes in ground floor of buildings may result in elimination of braces.This phenomenan, which called “soft story”, decreases the stiffness of stories and leads to collapse of building under severe earthquakes. Study of last earthquakes such as Bam on December 26 ,2003 and chichi-Thaiwan on September 20 ,1999 shows that many peaple missed their life because of soft stories created due to elimination of structural infills by changing residential buildings to commercial or architectural reasons.In this research, the soft story studied in short steel buildings with four stories by removing X-braces at first and second stories using nonlinear static and dynamic analyses. After removing braces, the stiffness of soft story increased gradually by providing rigid connections and using moment resisting frame and the replacement of braces with equivalent moment frame (with different stiffnessess) studied. The seismic design parameters such as transient and inherent dissplacements, ductility and energy dissipation capacity calculated and compared in various diagrames. In addition, the sttiffness of X-braced and moment resisting frames calculated using classical relations of solid mechanics and discussed. According toobtained results, the replacement of X-braces by an equivalent moment frame in a building leads to excessive drifts and less energy dissipation capacity. In addition, the findings of this paper is coin with specification requirements to avoid soft stories in buildings by avoiding stories with stiffness of 70 percent relative to above story.}, keywords = {Soft Story,Ductility,energy dissipation capacity,X-Brace,Nonlinear Static and Dynamic,Analysis}, title_fa = {مطالعه موردی کارایی لرزهای ناشی از ایجاد طبقه نرم در ساز ههای فولادی کوتاه و جایگزینی مهاربندها با قاب خمشی معادل}, abstract_fa = {بسیاری از تغییرات کاربری در طبقه همکف منجر به حذف مهاربند در طبقات می‌گردد و طبقه نرم در سازه شکل میگیرد. این پدیده منجر به از دست رفتن سختی در طبقات نرم و خرابی سازه در زلزله های شدید می‌گردد. لذا آیین نامه های لرزه ای ضوابط سخت گیرانه‌ای جهت مقابله با طبقه نرم در نظر گرفته‌اند. با مطالعه زلزله‌های گذشته همچون زلزله بم در پنجم دی ماه سال 1382یا زلزله چیچی تایوان در بیستم سپتامبر سال 1999، بیانگر آن است که انسان‌های بیشماری براثر ایجاد طبقه نرم ناشی از حذف مهاربندها و میانقاب‌ها به دلیل تغییر کاربری از مسکونی به تجاری یا دلایل معماری جان خود را از دست داده‌اند.در این تحقیق، اثرات حذف مهاربند ضربدری در طبقات پایینی ساختمان‌های فولادی کوتاه (4 طبقه) با استفاده از آنالیزهای استاتیکی و دینامیکی غیرخطی بررسی گردیده است. به منظور بررسی ضوابط آیین نامه‌های طراحی، سختی سیستم در طبقه نرم با استفاده از قاب خمشی فولادی به صورت تدریجی افزایش یافته و تاثیر جایگزینی مهاربندها در طبقه نرم با استفاده از قاب خمشی معادل (با سختی های مختلف) بررسی گردیده است و پارامترهای طراحی لرزه ای سیستم نظیر دریفت گذرا و ماندگار، ضریب شکل پذیری و جذب انرژی به صورت مقایسه در نمودارهایی ارایه شده اند، همچنین روابط کلاسیک محاسبه سختی سیستمهای مهاربند ضربدری و قاب خمشی ارایه و مورد بحث قرار گرفته اند. با توجه به نتایج، جایگزینی سیستم مهاربندی در یک طبقه با قاب خمشی معادل با سختی مشابه منجر به دریفت‌های بزرگتر و جذب انرژی کمتر میگردد.}, keywords_fa = {طبقه نرم,شکل پذیری,ظرفیت جذب انرژی,مهاربند ضربدری,تحلیل استاتیکی و دینامیکی غیرخطی}, url = {https://ceej.aut.ac.ir/article_408.html}, eprint = {https://ceej.aut.ac.ir/article_408_346284a32f5907fe4b5638320ce9cee9.pdf} } @article { author = {Miri1, M. and Rakhshanimehr, M. and Miri, F.}, title = {The effect of Cover, Pressure Strength, and bars corrosion on Cracking of Reinforced Concrete Structures}, journal = {Amirkabir Journal of Civil Engineering}, volume = {49}, number = {2}, pages = {251-262}, year = {2017}, publisher = {Amirkabir University of Technology}, issn = {2588-297X}, eissn = {2588-2988}, doi = {10.22060/ceej.2016.693}, abstract = {Reinforced concrete (RC) structures often suffer from damage due to corrosion of reinforcing steel caused by carbonation and/ or chloride contamination of concrete. Cracks can be caused erosion of structures when the time of their formation is a main parameter on performance structures And it is important that be able to predict with sufficient accuracy. thus the time prediction of corrosion initiation up to crack formation in the concrete cover is so important .in order to investigation of accuracy of analytical models result is used reability nonlinear behavior of concrete and inability to account for actual location of corroding reinforcing bars, finite element model is applied. in this research in order to simulation of analytical and crack growth method finite element software (FE) is used. To verification designed models, experimental models is applied and results of experimental and numerical models were compared. Results shows that cover reinforcement bars and concrete compressive strength are effective factors of starting cracking and with increasing these two parameters, inner pressure due to corrosion production 4 or 5 time will increase.}, keywords = {Corrosion of reinforcement,Concrete cover,Concrete crack,Numerical models}, title_fa = {بررسی عددی و آزمایشگاهی تأثیر پوشش، مقاومت فشاری و فشار ناشی از خوردگی آرماتور بر شروع ترک خوردگی در ساز ههای بتن آرمه}, abstract_fa = {سازه‌های بتن مسلح در مناطق خورنده، معمولاً از خرابی به علت خوردگی آرماتور‌ها، که می‌تواند ناشی از کربنات و یا نفوذ یون‌های کلر باشد، رنج می‌برند. افزایش حجم محصولات خوردگی نسبت به فولاد اولیه باعث ایجاد ترک در سازه شده، که می تواند منجر به تسریع کاهش عمر مفید آن شود. فلذا زمان شکل‌گیری ترکها یک پارامتر اصلی در عملکرد سازه بوده و مهم است که بتوان آن‌ را با دقت کافی پیش بینی کرد. به منظور بررسی دقت مدل‌های تحلیلی مبتنی بر مدلسازی رفتار غیر‌خطی بتن و تعیین محل خوردگی آرماتور، در این تحقیق از مدل اجزاء محدود استفاده شده‌ است. در ابتدا نمونه های آزمایشگاهی مختلفی ساخته شده و پس از نگهداری اولیه، تحت شرایط خوردگی تسریع شده قرار گرفته اند. محل و الگوی ترک مدلها در حین آزمایش و تا مرحله شکست کامل نمونه ها بطور دقیق ثبت شده اند. در مرحله بعد مدل عددی نمونه های فوق با استفاده از اجزای محدود ساخته شده و نتایج حاصل از روش‌های آزمایشگاهی و عددی با یکدیگر مقایسه شده‌اند. پس از اطمینان از صحت مدلهای عددی ساخته شده، اثر پارامترهای مختلف بر ترک خوردگی بتن مورد بررسی قرار گرفته است. نتایج حاکی از آن‌ است که پوشش آرماتور و مقاومت فشاری بتن از عوامل موثر در شروع ترک‌خوردگی می‌باشند و با افزایش این 2 پارامتر فشار داخلی ناشی از محصولات جهت شروع ترک‌خوردگی بیشتر خواهد شد.}, keywords_fa = {خوردگی آرماتور,پوشش بتن,ترک خوردگی بتن,مدلهای عددی}, url = {https://ceej.aut.ac.ir/article_693.html}, eprint = {https://ceej.aut.ac.ir/article_693_6aa04497f43df62800162d48b15d7dc2.pdf} } @article { author = {Karimi1, M. and Musavi Jahromi, S.H. and Shafai-Bajestan, M.}, title = {Pressure Fluctuations in Hydraulic Jump Investigation of Stilling Basin at Sudden Expansion}, journal = {Amirkabir Journal of Civil Engineering}, volume = {49}, number = {2}, pages = {263-272}, year = {2017}, publisher = {Amirkabir University of Technology}, issn = {2588-297X}, eissn = {2588-2988}, doi = {10.22060/ceej.2016.678}, abstract = {The hydraulic jump in the stilling basin can be considered macroscopically as a time-averaged steady, abruptly varied flow characterized by a free surface discontinuity and the formation of strong vortex that generates macro turbulent fluctuations.This paper are discussed the characteristics of pressure fluctuations in spatial hydraulic jumps with sudden expansion stilling basin. The effects of the channel expansion ratio and inflow condition on the dimensionless standard deviation of pressure fluctuations (cp') and extreme pressure fluctuations (Cp+, Cp-) in the hydraulic jump were examined. In this study many tests were conducted in a relatively large flume size of 0.8 meter wide and 12 meter length. data were presented for Froude numbers from 2.5 to 9.5 and channel expansions ratio (B1/B2) was 0.33, 0.5, 0.67 and 1. Pressure data were recorded by means of pressure transducers systems. A sampling frequency of 40 Hz was selected. The results show that the dimensionless standard deviation of pressure fluctuations and extreme pressure fluctuations of the hydraulic jump are dependent on the inflow Froude number and position from the toe of the jump. Fluctuating pressure at the position of about (10-30)Y1, can reach the maximal value. And indicates that the sudden expansion at the hydraulic jump decreases pressure fluctuations. The dimensionless standard deviation of pressure fluctuations (Cp') decreases on the order 43%, 38% and 19% for expansions ratio β = 0.33 , 0.5 and 0.7, respectively compared with classic jump.}, keywords = {Pressure fluctuations,Spatial hydraulic jump,Sudden expansion,Stilling basin}, title_fa = {بررسی نوسانات فشار در طول پرش هیدرولیکی در حوضچه واگرای ناگهانی}, abstract_fa = {پرش هیدرولیکی در حوضچه آرامش، از دیدگاه ماکروسکوپی، یک جریان ماندگار و متغیر ناگهانی است که با سطح جریان منقطع دوفازی و گرداب های قوی همراه است. فشار های نوسانی ناشی از تلاطم در پرش می تواند با ایجاد حفره، فرسایش و لرزش موجب آسیب قابل توجهی در حوضچه گردد. در این مقاله به مشخصات نوسانات فشار در پرش هیدرولیکی نوع s در مقاطع واگرای ناگهانی پرداخته شده است. تاثیر نسبت واگرایی مقطع و شرایط ورودی جریان در پارامتر بدون بعد انحراف معیار استاندارد نوسانات فشار (Cp') و فشارهای حدی (Cp+, Cp-) پرداخته شده است. به این منظور آزمایش‌ها در یک فلوم نسبتا بزرگ به عرض 8/0 و طول 12 متر در حوضچه آرامش با نسبت های واگرایی 33/0، 5/0، 67/0 و 1 در محدوده اعداد فرود بین 5/2 تا 5/9 صورت گرفت. داده های فشار با استفاده از مبدل فشار با فرکانس نمونه برداری 40 هرتز برداشت شده است. نتایج به دست آمده نشان می دهد که انحراف معیار نوسانات فشار و فشارهای حدی ناشی از پرش هیدرولیکی وابسته به عدد فرود جریان ورودی و موقعیت نقطه مورد نظر نسبت به پنجه پرش می باشد. به طوری که حداکثر ضرایب نوسانات فشار در فاصله 10 تا 30 برابر عمق اولیه پرش نسبت به پنجه پرش رخ می دهد. واگرایی در مقطع پرش سبب کاهش ضرایب نوسانات فشار می‌باشد. به طوری که در نسبت‌های واگرایی 33/0، 5/0 و 67/0 انحراف معیار نوسانات فشار به ترتیب برابر با 43%، 38% و 19 % در مقایسه با پرش کلاسیک کاهش می یابد.}, keywords_fa = {نوسانات فشار,پرش هیدرولیکی نوع s,واگرای ناگهانی,حوضچه آرامش}, url = {https://ceej.aut.ac.ir/article_678.html}, eprint = {https://ceej.aut.ac.ir/article_678_9709701bb5321b1c85c5024d18759e0e.pdf} } @article { author = {Rajaee, Taher and Jafari, Hamideh and Rahimi, Roghaye}, title = {Performance Improvement of Biological BOD in Rivers based on De-noising Comparison Wavelet-ANN Conjunction, GP, ANN and MLR Methods (Case Study:Karaj Dam Outlet Station)}, journal = {Amirkabir Journal of Civil Engineering}, volume = {49}, number = {2}, pages = {273-284}, year = {2017}, publisher = {Amirkabir University of Technology}, issn = {2588-297X}, eissn = {2588-2988}, doi = {10.22060/ceej.2016.710}, abstract = {This study considered artificial neural network (ANN), multi-linear regression (MLR), Genetic Programming (GP) and wavelet analysis and ANN combination (WANN), models for monthly water biological oxygen demand (BOD) in station Karaj Dam outlet and investigates the effects of data preprocessing on model performance using discrete wavelet. For this purpose, In the first proposed model, observed time series of BOD were decomposed into several subtime series at different scales by discrete wavelet transform. Then these subtime series were imposed as inputs to the ANN method. In the second proposed model, observed time series of BOD were decomposed at ten scales by wavelet analysis. Then, total effective time series BOD were imposed as inputs to the neural network model for prediction of BOD in one month ahead. Results showed that the wavelet neural network models performance was better in prediction rather than the neural network and multilinear regression models. The wavelet analysis model produced reasonable predictions for the extreme values. This model dropped the mean absolute percentage error for the MLR, GP, ANN and the first hybrid models from 1.87, 0.91, 0.65 and 0.46 respectively, to 0.44 and increased the Nash-Sutcliffe model efficiency coefficient from 0.23, 0.53, 0.73 and 0.81 to 0.83.}, keywords = {artificial neural network,BOD,De-noising,Karaj River,Wavelet transformy}, title_fa = {بهبود نتایج پیش بینی BOD رودخانه ها بر پایه نویززدایی با مقایسه مدل های موجک عصبی، برنامه ریزی ژنتیک، شبکه عصبی و رگرسیون خطی (مطالعه موردی: ایستگاه خروجی سد کرج)}, abstract_fa = {در این مطالعه مدل‌های شبکه عصبی مصنوعی، رگرسیون خطی چند متغیره، برنامه‌ریزی ژنتیک و ترکیب شبکه عصبی- موجک برای پیش بینی اکسیژن‌خواهی بیوشیمیایی ماهانه آب (BOD) در ایستگاه خروجی سد کرج بررسی شد و تأثیر پیش‌پردازش داده‌ها روی عملکرد مدل‌ها بوسیله تجزیه موجک مورد تحقیق قرار گرفت. به این منظور در مدل پیشنهادی اول، سری زمانی BOD مشاهداتی بوسیله توابع تبدیل مختلف در سطوح مختلفی به زیر سری‌ها تجزیه شدند و به عنوان ورودی در مدل شبکه عصبی قرار گرفتند. در مدل پیشنهادی دوم، سری زمانی BOD در ده سطح تجزیه شد. سپس حاصل جمع جبری زیرسری‌های مؤثر به عنوان ورودی مدل شبکه عصبی برای پیش‌بینی ماه آینده BOD درنظر گرفته شد. نتایج نشان داد که عملکرد پیش‌بینی مدل‌های ترکیبی موجک عصبی نسبت به شبکه عصبی، برنامه‌ریزی ژنتیک و رگرسیون بهتر است. این مدل ترکیبی برای مقادیر بیشینه نیز پیش‌بینی قابل قبولی را ارائه داده است. همچنین مدل ترکیبی دوم میانگین قدرمطلق خطا را برای مدل‌های رگرسیون، برنامه‌ریزی ژنتیک، شبکه عصبی و مدل ترکیبی اول، به ترتیب از 87/1 ، 91/0، 65/0 و 46/0 به 44/0 کاهش داد و ضریب کارایی را از 23/0، 53/0، 73/0 و 81/0 به 83/0 افزایش داد.}, keywords_fa = {اکسیژن خواهی بیولوژیکی,برنامه ریزی ژنتیک,تبدیل موجک,رودخانه کرج,شبکه عصبی,نویززدایی}, url = {https://ceej.aut.ac.ir/article_710.html}, eprint = {https://ceej.aut.ac.ir/article_710_c8edf50120124e42a7f81648686e5630.pdf} } @article { author = {Ehteshami, M. and Khorasani, M. and Ghadimi, H. and Hayatbini, N.}, title = {Analysis of Temporal and Periodic Changes of Groundwater Depth and Nitrate Concentration Using Time Series Modeling (Case Study: Kabudarahang Plain)}, journal = {Amirkabir Journal of Civil Engineering}, volume = {49}, number = {2}, pages = {285-294}, year = {2017}, publisher = {Amirkabir University of Technology}, issn = {2588-297X}, eissn = {2588-2988}, doi = {10.22060/ceej.2015.415}, abstract = {ABSTRACTIn this study, ground water level fluctuations and Nitrate concentrations of kabudarahang aquifer were investigated with application of time series models for modeling of ground water quantity and quality parameters. For data regarding the status of groundwater level and Nitrate concentration fluctuations in project area time series models were used to forecast the groundwater level and Nitrate concentration. Residual error analysis, comparison of observed and calculated ground water levels and Nitrate concentrations performed and finally a prediction model for ground water conditions in Kabudarahang aquifer developed. Predicted values were calibrated by the Box-Jenkins, Holt Winters and extrapolation axes models. A residual error analysis, based upon calculated and observed groundwater level and Nitrate concentration performed as a model verification tool and finally the Box Jenkins models were evaluated through portmanteau method and Akaike information criterion. The model verification results showed that the SARIMA model is the optimum algorithm to simulate seasonal input data variables. Model results showed that the groundwater level in this aquifer will endure a 6 meter decline in four upcoming years and indicated that the maximum Nitrate concentration would reach 50 mg/l in Bahman and shahrivar of 1390.}, keywords = {Time Series,Stochastic analysis,Groundwater Modeling,Nitrate Concentration,Kabudarahang}, title_fa = {ارزیابی تغییرات تراز و غلظت نیترات آب های زیرزمینی دشت کبودرآهنگ با استفاده از سری های زمانی}, abstract_fa = {منابع آب‌های زیرزمینی یکی از مهم‌ترین و باارزش‌ترین منابع آب به شمار می‌روند، شناخت صحیح و بهره‌برداری اصولی از آن‌ها به خصوص در مناطق خشک و نیمه‌خشک می‌تواند در توسعه پایدار بسیاری از فعالیت‌های کشاورزی، اجتماعی و اقتصادی آن منطقه تأثیر بسزایی داشته باشد. برای آگاهی از وضعیت نوسانات سطح و غلظت نیترات آب زیرزمینی در دشت کبودرآهنگ از مدل‌های سری زمانی برای پیش‌بینی وضعیت سطح آب‌زیرزمینی در طی سال‌های 1367-1386 و غلظت نیترات در سال‌های 1385-1389 استفاده گردید. توسط مدل‌های باکس-جنکینز، پیش‌بینی هیدروگراف 2 ساله و کموگراف یک ساله تهیه گردید. مدل‌های باکس‌جنکینز، هالت وینترز و برون‌یابی محوری، جهت واسنجی و پیش‌بینی داده‌ها استفاده گردید. تحلیل خطای باقیمانده‌ها و صحت‌سنجی مدل باکس جنکینز از طریق روش پرت مانتو و آکائیک صورت گرفت. نتایج مدل باکس جنکینز نشان داد که سطح آب‌زیرزمینی دشت در 4 سال آینده 6 متر افت خواهد داشت. مقدار متوسط غلظت نیترات در طی ماه‌های سال برابر با mg/l 48/08 است. نتایج تحلیل خطاهای مدل‌های کمی و کیفی (باکس جنکیز و هالت وینترز و برونیابی محوری ) که شامل SSE و RMSE و MAE بود نشان‌دهنده پتانسیل بهینه یابی توسط مدل باکس جنکینز میباشد.}, keywords_fa = {سری زمانی,مدلسازی,تراز آب زیرزمینی,نیترات,کبودرآهنگ}, url = {https://ceej.aut.ac.ir/article_415.html}, eprint = {https://ceej.aut.ac.ir/article_415_831a9a08e32e3200fc7d72bd23dffb6d.pdf} } @article { author = {Salahi, M.B and Parvizi, M. and Sedghi-Asl, M.}, title = {Laboratory Investigation of Non-Darcy Flow through Rounded Porous Materials}, journal = {Amirkabir Journal of Civil Engineering}, volume = {49}, number = {2}, pages = {295-304}, year = {2017}, publisher = {Amirkabir University of Technology}, issn = {2588-297X}, eissn = {2588-2988}, doi = {10.22060/ceej.2015.407}, abstract = {Application of aggregate coarse rockfill in hydraulic structures is increasing due to their special ‎properties and is imperative due to its importance and their specific characteristics. Accurate ‎investigation of the flow properties through coarse materials in order to determine hydraulic ‎parameters is one of the most important necessities considering high application such media in civil ‎works. On the other hands, there is less works about transitional flow through coarse materials. In ‎order to study the flow behavior through granular materials a packed column test was built. Some ‎experiments have done on three samples of rounded particles with average size of 10.348mm, ‎‎12.127mm and 17.785mm and seepage flow and upstream and downstream heads were recorded in ‎a certain intervals. By using some calculating and depicting some graphs, their behaviors have ‎evaluated. Using the relationship of flow velocity- hydraulic gradient, it was fund that such ‎relationship is non-linear and this is a strong criteria confirming non-Darcy flow. The evaluating of ‎results of this study by statistical indexes and its comparison by Ergun (1952), Kovacs (1981) and ‎Sidiropoulou et al (2007) relationships showed that the relation of Sidiropoulou et al (2007) is more ‎accurate than the other equations. The result of Reynolds number-friction factor curves has shown ‎that with increasing the grain size diameter, friction factor is decreased and Reynolds number is ‎increased.‎}, keywords = {Non-Darcy flow,Coarse material,Permeameter device,hydraulic gradient,Constant head test}, title_fa = {مطالعه آزمایشگاهی خصوصیات جریان درون مصالح متخلخل گردگوشه}, abstract_fa = {استفاده از مصالح درشت دانة سنگریزه‌ای در سازه های آبی بدلیل خصوصیات ویژة آنها روز به روز رو به افزایش می‌باشد. به دلیل ‏اهمیت جریان درون مصالح سنگریز مطالعه خصوصیات این نوع از جریان از اهمیت خاصی برخودار است. بررسی دقیق خصوصیات ‏جریان در مصالح درشت دانه و بدست آوردن پارامتر‌های هیدرولیکی با توجه به استفاده بسیار زیاد مصالح درشت دانه در کارهای ‏عمرانی، یکی از ضرورتهای مهم انجام تحقیقات بر روی جریان در این مصالح می‌باشد. از طرفی تحقیقات کمی بر روی جریان بینابینی ‏درون مصالح درشت دانه انجام گرفته است. بمنظور بررسی رفتار جریان درون مصالح دانه‌ای دستگاه پرمئامتری طراحی و ساخته شد. ‏آزمایش‌هایی بر روی سه نمونه ذرات سنگریزه‌ای گرد‌گوشه با اندازه قطرهای متوسط 348/10، 127/12و 785/ 17 میلیمتر انجام شد و ‏در زمان‌های مشخص دبی خروجی و تراز بالادست و پایین‌دست ثبت شد و با انجام محاسبات و رسم نمودارهایی خصوصیات آن‌ها مورد ‏ارزیابی قرار گرفت. با استفاده از نتایج آزمایشگاهی نمودار‌های سرعت – گرادیان هیدرولیکی رسم شد، که حاکی از غیر‌خطی بودن ‏رابطه بین سرعت و گرادیان هیدرولیکی می‌باشد و همین امر دلیل محکمی بر غیردارسی بودن جریان است. ارزیابی نتایج حاصل از این ‏تحقیق بوسیله شاخص آماری و مقایسه آن با روابط ارگان (1952)، کواکس(1981)، و سیدروپلو و همکاران(2007) نشان داد که رابطه ‏سیدروپلو و همکاران از قابلیت اعتماد بیشتری نسبت به دیگر معادلات برخوردار است. نتایج تحلیل نمودار عددرینولدز – فاکتور ‏اصطکاکی، نشان داد که هر چه قطر مصالح بزرگتر می‌شود فاکتور اصطکاکی کاهش و عدد رینولدز افزایش می‌یابد.‏}, keywords_fa = {جریان غیر دارسی,مصالح درشت دانه,دستگاه پرمئامتر,بار ثابت}, url = {https://ceej.aut.ac.ir/article_407.html}, eprint = {https://ceej.aut.ac.ir/article_407_b26ff5349ceb0856bae9d86a1c2d3c9b.pdf} } @article { author = {Ziaie Moayed, R. and Khatami, Seyed M.H and Allahyari, F.}, title = {Effect of Using Ion Exchange Solution in Increasing Bearing Capacity of Clayey Soils with Various Plasticity Index (PI)}, journal = {Amirkabir Journal of Civil Engineering}, volume = {49}, number = {2}, pages = {305-312}, year = {2017}, publisher = {Amirkabir University of Technology}, issn = {2588-297X}, eissn = {2588-2988}, doi = {10.22060/ceej.2015.417}, abstract = {So far, at the most of executive project in Iran, using CBR+4 ion stabilizer solution is a chemical ion-exchange experiments. The necessity of present study is the investigation about the characteristics of strength behavior of clayey soils with various PI stabilized by this method. The performance of stabilized soil samples by“CBR+4” ion-exchange solution in wetting-drying and freeze-thaw cycles also been studied for the first time in this study. In soil stabilization with CBR+4 solution Firstly, according to the amount of soils ion exchange, which is determined by a laboratory chemical test, the required amount of the stabilizer is determined. Then, At the most of executive project in Iran, using Tetrabromomethane (CBR+4) ion stabilizersolution is a chemical ion-exchange experiments. The necessity of present study is the investigationabout the characteristics of strength behavior of clayey soils with various plasticity index (PI) stabilizedby this method. The performance of stabilized soil samples by CBR+4 ion-exchange solution in wettingdryingand freeze-thaw cycles also been studied for the first time in this study. Firstly, in soil stabilizationwith CBR+4 solution the required amount of the stabilizer is determined, according to the amount ofsoils ion exchange, which is determined by a laboratory chemical test. Then, the samples are built intheir optimum moisture content and maximum dry densities and after curing the samples for two weeks,dry samples are tested. Soils samples are also tested in saturated condition after two weeks curing time.Saturated samples showed more increase in strength compared to dry samples. Stabilized soil sampleare also tested under 1 to 4 freeze-thaw and wetting-drying cycles. Tests results showed that usingCBR+4 stabilizer increase bearing capacity of clayey soils. This increase is higher in soils with lowerPI. Although freeze-thaw and wetting-drying cycles reduce soils bearing capacity, their strength aresignificantly more than the un-stabilized samples and is acceptable.}, keywords = {Soil Stabilization Ion Exchange CBR+4 PI California Bearing Ratio Test (CBR),Freeze-Thaw and Wetting- Drying Cycles}, title_fa = {تاثیر استفاده از محلول تبادل یونی CBR +4 در افزایش میزان باربری خاکهای رسی با شاخص خمیری مختلف}, abstract_fa = {تاکنون در اکثر پروژ ههای اجرایی در ایران روش کار برای استفاده از ماده تثبی تکننده یونی CBR+4 ، انجام آزمایشهای تبادل یونی شیمیایی بوده است. ضرورت انجام این تحقیق بررسی مشخصات رفتار مقاومتی نمون ههای خاک رسی با PI مختلف تثبیت شده به این روش با انجام آزمایشهای مکانیکی از جمله CBR+4 است. همچنین عملکرد نمونه های تثبیت شده خاک با محلول تبادل یونی CBR+4 در سیکلهای تر و خشک شدن و ذوب-انجماد نیز برای اولین بار در این تحقیق مورد مطالعه قرار گرفته است. در تثبیت خاک با محلول CBR+4 ابتدا با توجه به میزان تبادل یونی خا کها که بوسیله یک آزمایش شیمیایی انجام م یشود، میزان مورد نیاز مواد تثبی تکننده تعیین م یشود. سپس، نمون هها در درصد رطوبت بهینه و بیشترین چگالی خشک ساخته شده و پس از عم لآوری به مدت دو هفته، نمونه های خشک مورد آزمایش قرار گرفتند. همچنین نمونه های خاک پس از دو هفته عمل آوری در شرایط خیس خورده نیز مورد آزمایش قرار گرفت هاند. نمون ههای خیس خورده در مقایسه با نمونه های خشک افزایش مقاومت بیشتری نشان دادند. سپس نمون هها تحت 1 تا 4 سیکل انجماد-ذوب و خشک-تر قرار گرفت هاند. نتایج نشان میدهند استفاده از محلول CBR+4 ، باربری خاکهای رسی را افزایش میدهد این افزایش در خاک با PI کمتر، بیشتر است. اگرچه سیکلهای انجماد-ذوب و خشک-تر باربری خاک را کاهش میدهند، ولی مقاومت نمونه خاک رس تثبیت شده پس از اعمال سیکلهای مذکور به طور قابل توجهی بیش از نمونه های تثبیت نشده بوده و در حد قابل قبول است.}, keywords_fa = {تثبیت خاک,تبادل یونی,محلول تبادل یونی CBR+4,حد خمیری(PI),آزمایش میزان باربری کالیفرنیا (CBR),سیکلهای یخبندان-ذوب و تر و خشک شدن}, url = {https://ceej.aut.ac.ir/article_417.html}, eprint = {https://ceej.aut.ac.ir/article_417_9d7d198a2f91a9ba2891085186125eec.pdf} } @article { author = {Hosseini, M. and Hosseini, S. J.}, title = {Introducing New Equation for Predicting Penetration Rate of Tunnel Boring Machine}, journal = {Amirkabir Journal of Civil Engineering}, volume = {49}, number = {2}, pages = {313-322}, year = {2017}, publisher = {Amirkabir University of Technology}, issn = {2588-297X}, eissn = {2588-2988}, doi = {10.22060/ceej.2015.398}, abstract = {Tunnel Boring Machines (TBM) is among the most important machines for tunnel excavation purposes. Evaluation of the performance of these machines for excavation is of special importance due to the high cost of these machines. Prediction of the penetration rate is one of the indicators in evaluation of TBMs. There are various methods and equations for predicting the penetration rate, which are based on parameters related to the rock mass and specifications of the machine, and each of them has its own particular characteristics. Multivariable linear regressions, artificial neural networks, and adaptive neuro-fuzzy inference systems are among the highly efficient modeling and data pattern recognition methods. In this research, some equations have been proposed for predicting the penetration rate in Zagros I Tunnel by employing multivariable linear regression method and by considering the key parameters of the rock mass and the specifications of the TBM; the best equation was selected according to the results of statistical analysis. For verifying the validity of this equation, the penetration rate was calculated at certain parts of Ghomrood Tunnel. In comparison with the real values and results of other models, the outcomes of calculations indicate that predicted values for the penetration rate are of acceptable accuracy.}, keywords = {Penetration Rate,TBM,Rock,Water conveyance tunnel,Zagros I}, title_fa = {ارائه رابط هی جدید برای پی شبینی نرخ نفوذ ماشین حفاری تی بی ام ( TBM ) سنگ}, abstract_fa = {ماشینهای حفار تمام مقطع (TBM) از مهم ترین ماشینهای حفاری در تونلها به شمار می روند. بدلیل قیمت بالای ماشین، ارزیابی عملکرد در حفاری با استفاده از این ماشینها از اهمیت ویژه ای برخوردار است. یکی از شاخص ارزیابی عملکرد ماشین حفر تونل، پیش بینی نرخ نفوذ این دستگاه می باشد. روشها و روابط متنوعی برای پیش بینی نرخ نفوذ وجود دارد که هر کدام ویژگیهای خاص خود را دارد و بر اساس پارامترهای مربوط به توده سنگ و مشخصات ماشین ارائه شده اند. روشهای رگرسیون خطی چند متغیره، شبکه عصبی و سیستم استنتاجی تطبیقی فازی عصبی از روشهای با کارایی بالا در مدل سازی و تشخیص الگو در داده ها می باشند. در این تحقیق با بکارگیری روش رگرسیون خطی چند متغیره و با در نظر گرفتن پارامترهای کلیدی توده سنگ و ماشین حفر تونل (TBM) روابطی برای پیش بینی نرخ نفوذ در تونل زاگرس 1 ارائه گردید و بر اساس تحلیلهای آماری بهترین رابطه انتخاب گردید. برای بررسی اعتبار سنجی، نرخ نفوذ در بعضی مقاطع تونل قمرود توسط رابطه پیشنهادی محاسبه شد. نتایج محاسبات در مقایسه با مقادیر واقعی و نتایج سایر مدلها نشان می دهد مقادیر پیش بینی شده نرخ نفوذ توسط رابطه پیشنهادی از دقت قابل قبولی برخوردار است.}, keywords_fa = {نفوذ ماشین حفاری تی بی ام سنگ,تونل انتقال آب زاگرس 1}, url = {https://ceej.aut.ac.ir/article_398.html}, eprint = {https://ceej.aut.ac.ir/article_398_ca4efa820f3a57293096eed41869265e.pdf} } @article { author = {S. Kolbadi, S. Mohammad and Rasti Ardakani, Reza}, title = {Evaluation of Soil-Structure Interaction Parameters in Static and Dynamic Response of the Retaining Wall}, journal = {Amirkabir Journal of Civil Engineering}, volume = {49}, number = {2}, pages = {323-334}, year = {2017}, publisher = {Amirkabir University of Technology}, issn = {2588-297X}, eissn = {2588-2988}, doi = {10.22060/ceej.2016.864}, abstract = {Doing deep excavation in the urban limited spaces, the stabilization of massive soil slope and construction of large coastal walls require using of new methods and accurate calculation and analysis. So, in this study the finite element method (FEM) with ABAQUS software was used to modeling of the retaining wall. To evaluation of wall and soil behavior accurately, solid element and nonlinear behavior material was used to demonstrate more exactly responses of retaining wall. Also the structure response calculated for different parameters in concrete and soil. More than 50 analysis are used in this study. Sensitive analysis in interaction parameters and material behavior is considered to calculate the maximum displacement at the top and shear stress at button. It is shown that density changes are more important in the static and dynamic response of structures, but in dynamic analysis this parameter 30 percent more affect to the response comparing to static analysis.}, keywords = {Soil-structure interaction,Non-linear behavior of Drucker-,Prager,Retaining wall,Sensitive analysis,Abaqus}, title_fa = {بررسی پارامترهای اندرکنشی خاک و سازه در پاسخ های استاتیکی و دینامیکی دیوار حائل}, abstract_fa = {انجام گود برداری های عمیق در فضاهای محدود شهری، تثبیت شیروانی های خاکی حجیم و احداث دیوارهای ساحلی بلند، مستلزم بهره گیری از روشهای نوین و دقیق تحلیل و محاسبه است. در این مقاله جهت مدل سازی و تحلیل، نرم افزار اجزاء محدود Abaqus به خدمت گرفته شد. جهت بررسی دقیق تر رفتار دیوار و خاک، از المان Solid و نمایش واقعی رفتار دیوار، از مدل رفتاری غیر خطی برای هر دوع مصالح بتن و خاک استفاده شده است. در این مطالعه با انجام بیش از 50 تحلیل در حالت استاتیکی و دینامیکی با تحلیل حساسیت روی پارامترهای اندرکنشی و رفتاری مصالح، مقدار پاسخ سازه که همان بیشینه جابجایی دیوار درنظر گرفته شد، محاسبه و نشان داده شد که مهم ترین پارامتر اندرکنشی در حالت تحلیل استاتیکی و دینامیکی، چگالی خاک است و این میزان حساسیت در بارهای لرزه ای نسبت به تحلیل استاتیکی، حدود 30 درصد افزایش خواهد یافت.}, keywords_fa = {اندرکنش خاک-سازه,مدل غیرخطی دراکر پراگر,دیوار حائل,تحلیل حساسیت,Abaqus}, url = {https://ceej.aut.ac.ir/article_864.html}, eprint = {https://ceej.aut.ac.ir/article_864_51e352ca9935e4fd6b0976fd9a480423.pdf} } @article { author = {Hejazi, M. and Fathi, F. and Sadrarhami, H.R.}, title = {Study of Mechanical Properties of Structural Lightweight Concrete Reinforced with Hybrid Fibers}, journal = {Amirkabir Journal of Civil Engineering}, volume = {49}, number = {2}, pages = {335-346}, year = {2017}, publisher = {Amirkabir University of Technology}, issn = {2588-297X}, eissn = {2588-2988}, doi = {10.22060/ceej.2015.555}, abstract = {In this research the mechanical properties of structural lightweight concrete including compressive, tensile and flexural strengths and energy absorption using five types of fibres (industrial and scrap steel, glass, polypropylene and straw) in the form of single type of fibre or combination of two or three types of fibres have been studied. At the first stage, two reference samples of lightweight concrete and normal concrete without fibres are produced. At the second stage, samples of lightweight concrete with single type of fibres of volume percentages of 0.1, 0.25, 0.4, and 0.5 are made. At the third stage, samples of lightweight concrete containing twin combined forms of fibers with volume percentages of (0.1, 0.4), (0.4, 0.1) and (0.25, 0.25) are produced. At last stage, samples of lightweight concrete with triad combination forms of fibres with volume percentages of (0.1,0.1,0.3), (0.1,0.3,0.1) and (0.3,0.1,0.1) are produced. Obtained results indicate that samples with combination of two types of fibres have had the best behaviour compared to other samples. The highest compressive strength have been resulted from the combination of industrial steel and polypropylene fibres and the highest tensile and flexural strengths have been obtained from the combination of glass and polypropylene fibres. The highest energy absorption is related to the combination of industrial steel and glass fibres.}, keywords = {Structural Lightweight Concrete,Steel Fibre,Glass Fibre,Polypropylene Fibre,Hybrid Fibres,Mechanical Properties}, title_fa = {بررسی خواص مکانیکی بتن سبک ساز های با استفاده از الیاف ترکیبی}, abstract_fa = {در این تحقیق خواص مکانیکی بتن سبک سازه‌ای، شامل مقاومت فشاری، کششی، خمشی و جذب انرژی با استفاده از 5 نوع الیاف (فولاد صنعتی و ضایعاتی، شیشه، پلی‌پروپیلن و کاه) به صورت تک الیاف و ترکیبی (2تایی و 3تایی) مورد بررسی قرار گرفته است. روند تحقیق به این صورت بوده است که ابتدا 2 طرح شاهد از بتن سبک سازه‌ای و بتن معمولی بدون الیاف تهیه شده است. سپس، نمونه‌های بتنی سبک الیافی، به صورت تک الیاف با درصدهای حجمی 1/0، 25/0، 4/0 و 5/0، تهیه شده است. در مرحلة سوم، نمونه‌های بتنی سبک الیافی‌، به صورت ترکیب دوتایی از الیاف با درصد‌های حجمی (1/0 و 4/0)، (4/0 و 1/0) و (25/0 و 25/0) درست شده است. و در پایان، نمونه‌های بتنی سبک الیافی،‌ به صورت ترکیب سه تایی از الیاف با درصدهای حجمی (1/0، 1/0 و 3/0)، (1/0، 3/0 و 1/0) و (3/0، 1/0 و 1/0) تهیه شده است. نتایج حاصل از این تحقیق نشان داد که در بین نمونه‌های ساخته شده، نمونه‌های دارای ترکیب دوگانه، عملکرد بهتری نسبت به سایر نمونه‌ها داشته است. از ترکیب الیاف فولاد صنعتی و پلی‌پروپیلن بیشترین مقاومت فشاری و از ترکیب الیاف شیشه و پلی‌پروپیلن بیشترین مقاومت کششی و خمشی حاصل شده است. و بیشترین جذب انرژی نیز مربوط به ترکیب الیاف فولاد صنعتی و شیشه بوده است.}, keywords_fa = {سبک سازهای,الیاف فولادی,الیاف شیشه,الیاف پلی پروپیلن,الیاف ترکیبی,خواص مکانیکی}, url = {https://ceej.aut.ac.ir/article_555.html}, eprint = {https://ceej.aut.ac.ir/article_555_94964a05aef75a0381ae9fe6252ce6f2.pdf} } @article { author = {Mohebbi, M. and Bakhshinezhad, S.}, title = {Designing Variable Stiffness Semi-Active Tuned Mass Damper for Nonlinear Structures}, journal = {Amirkabir Journal of Civil Engineering}, volume = {49}, number = {2}, pages = {347-362}, year = {2017}, publisher = {Amirkabir University of Technology}, issn = {2588-297X}, eissn = {2588-2988}, doi = {10.22060/ceej.2016.704}, abstract = {In this paper, designing variable stiffness semi-active tuned mass damper (SATMD) formitigating the responses of nonlinear structures under earthquake excitation has been studied. Two semiactive control algorithms based on instantaneous optimal control and clipping control concept as well asmodified balance control have been developed to determine the optimal stiffness of SATMD for nonlinearstructures in each time step. For determining optimal parameters of semi-active control system includingthe weighting matrices in performance index of control algorithm as well as the maximum and minimumvalues of SATMD stiffness, an optimization problem for minimization of structure maximum response hasbeen defined where genetic algorithm (GA) has been used for optimization. For numerical simulations, aneight-story nonlinear shear building with bilinear hysteresis behavior has been subjected to a white noiseexcitation and optimal SATMDs have been designed. The results showed that optimal variable stiffnessSATMD using both control algorithms has been effective in suppressing the seismic responses of nonlinearstructure. Also, variable stiffness SATMD shows better performance than TMD and variable dampingSATMD in structural response controlling. Comparing the performance of the variable stiffness SATMDunder testing earthquakes which were different from design record, showed that the efficiency of SATMDdepends on the characteristics of excitation, hence design record needs to be chosen properly.}, keywords = {Variable stiffness semi-active tuned,mass damper,Non-linear structures,Semi-Active Control,Clipped optimal control algorithm,Modified balance control algorithm}, title_fa = {طراحی میراگر جرمی تنظیم شده ی نیمه فعال با سختی متغیر برای سازههای غیرخطی}, abstract_fa = {در این مقاله به طراحی مکانیزم میراگر جرمی تنظیم شده‌ی نیمه‌فعال با سختی متغیر برای کاهش پاسخ سازه‌های غیرخطی تحت اثر زلزله پرداخته شده است. تنظیم پارامتر سختی در هر لحظه، بر اساس دو الگوریتم کنترلی نیمه‌فعال توسعه یافته‌ی متناسب با رفتار سازه‌های غیرخطی شامل 1) کنترل بهینه‌ی آنی و قانون کنترل برشی و 2) کنترل بالانس اصلاح شده صورت گرفته است. برای تعیین مقادیر بهینه‌ی پارامترهای سیستم کنترل نیمه‌فعال (شامل ماتریس‌های وزنی در تابع عملکرد الگوریتم کنترل نیمه‌فعال و مقادیر حداقل و حداکثر سختی) یک مسئله‌ی‌ بهینه‌سازی با تابع هدف حداقل کردن حداکثر تغییر مکان جانبی نسبی سازه تعریف و با استفاده از الگوریتم ژنتیک حل شده است. برای آنالیز عددی یک قاب ساختمانی هشت طبقه‌ی برشی‌ با رفتار دوخطی هیسترسیس انتخاب و به طراحی مکانیزم کنترل نیمه‌فعال تحت اثر اغتشاش سفید پرداخته شده است. نتایج بررسی‌ها نشان می‌دهد که مکانیزم کنترل نیمه‌فعال طراحی شده بر اساس دو الگوریتم‌های کنترلی، عملکرد مشابه و مناسبی در کاهش حداکثر تغییر مکان جانبی نسبی سازه‌های غیرخطی داشته است. همچنین بررسی کارایی میراگر جرمی نیمه‌فعال با سختی متغیر تحت ارتعاش طراجی و تحریکات لرزه‌ای با محتوای فرکانسی متفاوت نشان می‌دهد که این مکانیزم در کاهش پاسخ‌ سازه با رفتار غیرخطی، موثرتر از سیستم غیرفعال و نیمه‌فعال با میرایی متغیر می‌باشد.}, keywords_fa = {میراگر جرمی تنظیم شده ی نیمه فعال با سختی متغیر,سازههای غیرخطی,الگوریتم کنترلی بهینه ی برشی,الگوریتم کنترلی تعادل اصلاح شده,الگوریتم ژنتیک}, url = {https://ceej.aut.ac.ir/article_704.html}, eprint = {https://ceej.aut.ac.ir/article_704_efc7d3b6cd5703321aba7a92dbcf178b.pdf} } @article { author = {Gholami, Mohsen and Ajalloeian, Rasoul}, title = {Comparison Between Selected Experimental Methods And Statistical And Artificial Neural Network For Landslide Hazard Zonation Case Study: Behesht Abad Dam Reservoir}, journal = {Amirkabir Journal of Civil Engineering}, volume = {49}, number = {2}, pages = {363-378}, year = {2017}, publisher = {Amirkabir University of Technology}, issn = {2588-297X}, eissn = {2588-2988}, doi = {10.22060/ceej.2015.374}, abstract = {In order to decrease the destructions due to landslides, it’s important and unavoidable to recognize and to map the hazard zonations. For this, different mehods are utilized by researchers in other countries with specific conditions. In this paper, landslide inventory map has been prepared and then the effective parameters on the landslides in the study area have been investigated. Finally, some empirical methods such as Mora-Varson and Nilson methods with bivariate Statistical and Artificial Neural Network(ANN) methods are selected by using comparison of various methods between original locations and this study area in Behesht Abad Dam reservoir. In consequence of landslide hazard zonation mapping by above mentioned methods, some relations including empirical Probability Factor(P), Landslide Index(Li) and Reciever Operating Characteristic(ROC) Curves are used to evaluate the accuracy of each method. Finally, the results of ROC curves and calculation of Area Under ROC Curve(AUC) are based for evaluation of accuracy. Therefore, Artificial Neural Network and Statistical methods are selected to provide suitable maps in this area.}, keywords = {Landslide Hazard Zonation,Nilson Method,Mora-Vahrson Method,Statistical Method,Artificial Neural Network (ANN),Reciever Operating Characteristic,(ROC) Curve}, title_fa = {مقایسه ی روشهای انتخابی تجربی و روشهای آماری و شبکه ی عصبی مصنوعی برای پهنه بندی خطر زمین لغزش(مطالعه ی موردی در مخزن سد بهشت آباد)}, abstract_fa = {به منظور کاهش خسارتهای ناشی از زمین‌لغزش، شناسایی پهنه‌های دارای پتانسیل خطر زمین‌لغزش و به نقشه در آوردن آن‌ها امری ضروری و اجتناب‌ناپذیر است. برای انجام این امر، روش‌های متعددی توسط محققین در کشورهای مختلف مورد استفاده قرار‌گرفته است که هر یک از آنها تحت شرایط ویژه‌ای ارائه شده‌اند. در این تحقیق، پس از تهیه‌ی نقشه ‌پراکنش زمین‌لغزش‌های قدیمی و بررسی عوامل مؤثر در زمین‌لغزش‌های محدوده مخزن سد بهشت‌آباد و نیز مقایسه هریک از روش‌های پهنه‌بندی و محل ابداع این روش‌ها با مورد مطالعه، روش‌های تجربی نیلسن و مورا-وارسون به همراه روش آماری دومتغیره و روش شبکه‌ی عصبی مصنوعی برای پهنه‌بندی خطر زمین‌لغزش انتخاب شده‌اند. در ادامه پس از تهیه‌ی نقشه‌های پهنه‌بندی خطر زمین‌لغزش، برای ارزیابی دقت این نقشه‌ها، از روش‌های احتمال تجربی، اندیس لغزش و نیز ترسیم منحنی ROC استفاده شده است. در نهایت نتایج حاصل از ترسیم منحنی ROC و محاسبه سطح زیر این منحنی مبنای ارزیابی دقت روش‌های پهنه‌بندی قرار گرفت که نتیجه آن در این محدوده، انتخاب روش آماری و روش شبکه‌ی عصبی مصنوعی(ANN) به عنوان روش‌هایی مناسب برای تهیه‌ی نقشه‌ی پهنه‌بندی خطر زمین‌لغزش بوده است.}, keywords_fa = {پهنه بندی خطر زمین لغزش,روش نیلسن,روش مورا-وارسون,روش آماری دو متغیره,روش شبکه ی عصبی مصنوعی(ANN),منحنی ROC}, url = {https://ceej.aut.ac.ir/article_374.html}, eprint = {https://ceej.aut.ac.ir/article_374_c7cb281a91f5251c880ea372318134fa.pdf} } @article { author = {Siadat, S. A. and Mokhtari, J.}, title = {Investigation of Coagulant Type Effect on Wet–Spinning Process of Regenerated Silk Fibroin}, journal = {Amirkabir Journal of Civil Engineering}, volume = {49}, number = {2}, pages = {379-388}, year = {2017}, publisher = {Amirkabir University of Technology}, issn = {2588-297X}, eissn = {2588-2988}, doi = {10.22060/ceej.2015.371}, abstract = {Regenerated silk fibroin (RSF) with various concentrations, 8, 10, 12.5 and 13% (w/w), was dissolved in N-methyl morpholine N-oxide (NMMO) to prepare spinning solutions. The effect of several coagulants such as methanol, ethanol and 1-propanol, and temperatures of spinning, 95, 110 and 120 °C, on the wet spinnability of the silk fibroin solutions were investigated by means of observation of wet spun fibers in various concentrations and coagulant baths (without any post drawing performance) and by measuring their tenacities at break. Undrawn good continuous and bead free fibers with high tenacity and elongation behavior, 1.6 cN/dtex and 34.25% respectively, were obtained at the concentration of 8% (w/w) and temperature of 95 °C and with presenting of methanol coagulant. The results showed that by increasing concentrations in 10, 12.5 and 13%, the tenacity decreases, 0.81, 0.70 and 0.20 cN/dtex, respectively. Tenacity of the fibers obtained in 1-propanol, 0.6 cN/dtex, was lower than those in ethanol, 0.8 cN/dtex, and methanol, 1.6 cN/dtex, coagulation bath. Therefore these results showed that the coagulant chemical type strongly influences the wet spinnability of undrawn regenerated silk fibers.}, keywords = {Regenerated Silk Fibroin N,Methyl Morpholine N,Oxide Coagulants Wet Spinnability Tenacity}, title_fa = {بررسی تاثیر نوع انعقادگر در فرآیند ترریسی فیبروئین ابریشم بازیافتی}, abstract_fa = {فیبروئین ابریشم بازیافتی با غلظت های مختلف 8، 10، 5/12 و (w/w) 13% در حلال N - متیل مورفولین N - اکساید حل شد و محلول های ریسندگی با غلظت های مختلف حاصل گردید. تاثیر انواع انعقادگرها شامل: متانول، اتانول و 1- پروپانول و همچنین دماهای ریسندگی 95، 110 و °C 120 در فرآیند ترریسی محلول فیبروئین ابریشم مورد بررسی قرار گرفت. استحکام در پارگی الیاف بدست آمده در غلظت ها و حمام های انعقاد مختلف (بدون اعمال هیچ گونه فرآیند کشش) اندازه گیری و محاسبه شد. الیاف ممتد بدون ریز دانه در طول آن همراه با استحکام و ازدیاد طول نسبی تا حد پارگی بالا (به ترتیب cN/dtex 6/1 و 25/34%) در غلظت (w/w) 8% و دمای ریسندگی °C 95 و با استفاده از حمام انعقاد متانول بدست آمد و همچنین مشاهده شد که با افزایش غلظت از 8 به 10، 5/12 و (w/w) 13%، استحکام کاهش یافته و به ترتیب برابر با 81/0، 70/0 و cN/dtex 20/0 گردیده است. استحکام الیاف بدست آمده از حمام انعقاد 1- پروپانول نیز برابر با cN/dtex 6/0 بوده که کمتر از حمام های انعقاد اتانول (cN/dtex 8/0) و متانول ( cN/dtex6/1) می باشد و این نتایج حاکی از آن است که نوع ساختار شیمیائی انعقادگر بر توانایی ترریسی الیاف ابریشم بازیافتی کشیده نشده تاثیرگذار می باشد.}, keywords_fa = {فیبروئین ابریشم بازیافتی,N-متیل مورفولین N-اکساید,انعقادگر,ترریسی,استحکام}, url = {https://ceej.aut.ac.ir/article_371.html}, eprint = {https://ceej.aut.ac.ir/article_371_b2a84ac4b0eb3751c8f538173786a75c.pdf} } @article { author = {Nejad, F. and Karimi, N. and Zakeri, H.}, title = {Providing a new criterion to evaluate the skid resistance of asphalt pavement}, journal = {Amirkabir Journal of Civil Engineering}, volume = {49}, number = {2}, pages = {389-402}, year = {2017}, publisher = {Amirkabir University of Technology}, issn = {2588-297X}, eissn = {2588-2988}, doi = {10.22060/ceej.2016.591}, abstract = {The friction of a pavement surface indicates safety of a pavement. Pavement friction properties depend on pavement surface’s microtexture and macrotexture characteristics. Recently, considerable attention has been paid by researchers to find new methods and procedures for more accurate and quick measurement of the pavement skid resistance. Most of the proposed approaches in this regard have been in the range of non-contact methods, the use of laser and digital images. It has been found that image processing as a non-contact method with adequate precision and high speed can prove to be a promising and effective approach for further research on determining the pavement skid resistance. In this paper an intelligent system based on image processing is introduced which analyzes the texture of the pavement and presents a new index for pavement skid resistance by taking the effects of horizontal, vertical and diagonal components of its texture into consideration. By comparing the results of the proposed system and the corresponding British pendulum test results (BPN) it can be said that, the proposed system through using the image processing technology and more accurate assessment of pavement textures is capable of better recognizing the pavement textures and can produce repeatable results associated with the pavement skid resistance.}, keywords = {Skid Resistance,Safety,Pavement Texture,Image processing,Expert Systems}, title_fa = {ارائه یک معیار جدید ارزیابی مقاومت لغزندگی روسازی آسفالتی}, abstract_fa = {اصطکاک سطح یک روسازی نشان دهنده ایمنی روسازی است. ویژگی‌های اصطکاکی یک روسازی به مشخصات بافت ریز و بافت درشت سطح آن روسازی بستگی دارد. امروزه محققان به دنبال ارائه روش‌هایی هستند که با دقت و سرعت بالایی مقاومت لغزشی روسازی را اندازه‌گیری کنند. راهکارهای ارائه شده در این زمینه بیشتر در محدوده روش‌های غیر تماسی ، استفاده از لیزر و تصاویر دیجیتال است. نتایج به دست آمده نشان می‌دهد که پردازش تصویر به عنوان یک روش غیر تماسی و با دقت قابل قبول و سرعت بالا، می‌تواند زمینه خوبی برای تحقیقات بعدی درباره تعیین مقاومت لغزشی روسازی باشد. در این مطالعه سیستم هوشمندی بر مبنای پردازش تصویر معرفی می‌شود که قادر به آنالیز بافت روسازی و ارائه یک شاخص جدید برای مقاومت لغزشی روسازی با در نظر گرفتن تاثیر اجزای افقی، قائم و قطری بافت روسازی در آن است. با مقایسه نتایج نهایی سیستم پیشنهادی و نتیجه آزمایش پاندول بریتانیایی (BPN) متناظر با آنها می‌توان گفت که، سیستم پیشنهادی با بهره‌گیری از تکنولوژی پردازش تصویر و بررسی بافت روسازی قادر است بافت روسازی را درک کرده و نتایج تکرارپذیری در ارتباط با قابلیت لغزشی روسازی ارائه کند.}, keywords_fa = {مقاومت لغزشی,ایمنی,بافت روسازی,پردازش تصویر,سیستم خبره}, url = {https://ceej.aut.ac.ir/article_591.html}, eprint = {https://ceej.aut.ac.ir/article_591_fcce043085ccbce62d2adf09bf53a361.pdf} } @article { author = {Vatani Oskouei, A. and Afzali, M. and Madadipour, M.}, title = {Effect of reinforcement the mortar on adobe walls performance}, journal = {Amirkabir Journal of Civil Engineering}, volume = {49}, number = {2}, pages = {403-416}, year = {2017}, publisher = {Amirkabir University of Technology}, issn = {2588-297X}, eissn = {2588-2988}, doi = {10.22060/ceej.2016.700}, abstract = {Present study investigates an experimental performance of mud brick wall under static lateralload. The size of bricks was about 22×22×7 cm3 (face × bed × end). For wall specimens, two types mortarwas used: a) non-reinforced mortar, b) reinforcement mortar. For reinforcement mortar many types such as:metal mesh (mesh size: 0.5 and 0.75 inches), polymeric mesh (mesh size: 10 and 25 mm) and palm fiberconsidered was used. First mechanical properties of each types of mortar have been determined. Then the 12wall with dimensions of 120 × 120 × 22 cm3 are made with six different kinds of mortar. Walls are loadedunder static lateral load in order to evaluate their cracks pattern, load capacities, deformability and energyabsorption characteristics. Cracks in the specimens occurred between the first and the second row that causedthe failure. The mortar was vulnerable part of conventional walls (unreinforced mortar). Ultimate strengthof walls with mortar reinforced by polymer mesh (mesh size was 25 × 25 mm) increased the load andenergy capacity to 83.04% and 158% respectively. The palm fibers increased the load carrying capacity about82.14% and energy absorption capacity about 247%. Test result was shown that using palm fiber and polymermesh with diameter of 25 mm in mortar can increase adobe wall performance.}, keywords = {Mud brick,Static lateral load tests,Palm fiber,Mortar,Mud brick wall,Metal mesh}, title_fa = {تاثیر تسلیح ملات بر عملکرد دیوارهای خشتی}, abstract_fa = {با توجه به سالنامه اماری درصد قابل توجهی از ساختمان‌های مسکونی در ایران مربوط به ساختمان‌های خشتی و سنتی می‌باشد. این ساختمان‌های کوتاه مرتبه به علت داشتن سیستم سازه‌ای سنتی قادر به تحمل بارهای جانبی ناشی از زلزله نیستند. در این مقاله راهکارهایی برای افزایش عملکرد این ساختمان‌ها در برابر زلزله ارائه شده است. بدین منظور تعداد 12 عدد دیوار خشتی با انواع مختلف ملات: معمولی، مسلح شده با توری فلزی (با قطر چشمه 7/12 و 05/19 میلی‌متر(5/0 و 75/0 اینچ))، توری پلی‌مری (با قطر چشمه 10 و 25 میلی‌متر) و لیف خرما، در ابعاد 22×120×120 سانتی‌متر برای بررسی رفتار دیوار و ملات ساخته شده‌اند. دیوارها تحت بار جانبی یکنوا بارگذاری شده تا نوع ترک‌ها، نیروی نهایی، تغییرشکل نهایی و جذب انرژی آنها بدست آیند. نتایج‌ حاصل از آزمایش نشان می‌دهد که ملات به عنوان یکی از ضعیف‌ترین اجزای دیوار می‌باشد. در دیوارهای مسلح شده با توری پلی‌مری با قطر چشمه 25 میلی‌متر افزایش 83 درصدی در بار نهایی و افزایش 165 درصدی در جذب انرژی مشاهده شده است. در دیوارهای مسلح شده با لیف‌خرما افزایش 82 درصدی تغییر مکان نهایی و افزایش 162 درصدی در جذب انرژی مشاهده شده است. بنابراین می‌توان با تقویت ملات با توری و لیف خرما عملکرد دیوار را بهبود بخشید.}, keywords_fa = {خشت,آزمایش بارگذاری جانبی,لیف خرما,توری فلزی,توری پلیمری}, url = {https://ceej.aut.ac.ir/article_700.html}, eprint = {https://ceej.aut.ac.ir/article_700_90583b9313fca70f291b5fea05ec9842.pdf} }